Mitsubishi Electronics EX200U Adjusting the projected image, Adjusting the projection angle

Page 23

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the

image is positioned where you want it, release the quick-release button to lock the foot in position.

2. Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are

2

1

not perpendicular to each other, the projected image becomes trapezoidal. To

 

 

correct this situation, see "Correcting keystone" on page 24 for details.

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

•Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

•This function is only available when a PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

In the right figure, (A) Focus Ring, (B) Zoom Ring

 

 

1.

Adjust Zoom. (using (B) Zoom Ring)

 

A

2.

For the short distance/large screen, dial the ring fully to Wide end.

Tele

Wide

3.

For the long distance/small screen, dial the ring fully to Tele end.

 

B

Adjust Focus. (using (A) Focus Ring)

 

 

4.

Move the product back and forth to adjust the screen size.

 

 

5.

Adjust Focus again if necessary.

 

 

ENGLISH

EN-23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents EX200U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewProjector Controls and functionsMagnifying and searching for details on page 24 for Remote controlRemote control effective range Obtaining a preferred projected image size Positioning your projectorChoosing a location EN-12 Front projection Layout of the projectorTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Entering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenHow to use the Timer On key? Setting the presentation timerTo cancel the timer, perform the following steps Freezing the image Adjusting the soundHiding the image Locking control keysShutting down the projector Direct power offPersonalizing the projector menu display Menu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color System Setup Basic menu System Setup Advanced menu Change password EN-38 Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX200U VLT-EX240LP Replacing the lampResetting the lamp timer Light Status & Description Power Temp Lamp Power events IndicatorsTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Replacement partEN-49 Mitsubishi Electric Corporation
Related manuals
Manual 49 pages 20.98 Kb

EX200U specifications

The Mitsubishi Electronics EX200U and ES200U are innovative and highly efficient solutions designed to meet the demands of modern automation and control systems. Tailored for both industrial and commercial applications, these servo drives enhance performance while ensuring reliability and precision.

At the core of the EX200U and ES200U models is advanced motion control technology. These servo drives leverage high-resolution feedback systems to deliver exceptional positioning accuracy, which is critical in applications such as robotics, CNC machinery, and advanced manufacturing processes. The integration of Mitsubishi’s proprietary algorithms allows for real-time processing of motion commands, enabling smoother operations and reducing mechanical stress.

One of the standout features of the EX200U and ES200U is their versatility. These servo drives support a wide range of motor types, including synchronous and asynchronous motors, making them suitable for various operational demands. With scalable performance, users can easily adjust settings to match the specific needs of their applications, whether they require high speed or high torque.

Energy efficiency is another essential characteristic of the EX200U and ES200U. Both models are designed to minimize energy consumption without sacrificing performance. The incorporation of regenerative braking technology allows for energy to be recaptured during deceleration, contributing to lower operational costs and a smaller environmental footprint.

The user-friendly interface of the EX200U and ES200U simplifies configuration and monitoring. With intuitive software tools, engineers can quickly set up, program, and fine-tune the drives. The ability to interface seamlessly with Mitsubishi’s broader automation ecosystem enhances operational cohesion, allowing for standardized control and data analytics across multiple devices.

Safety is also prioritized in the design of the EX200U and ES200U. These servo drives come equipped with integrated safety features, including safe torque off and error handling capabilities that protect both equipment and personnel. Compliance with international safety standards further reinforces their reliability in industrial environments.

In summary, the Mitsubishi Electronics EX200U and ES200U servo drives represent a blend of advanced technology, user-centric design, and energy efficiency. With their impressive features and capabilities, they are well-equipped to handle the demands of contemporary automation, providing users with reliable and precise control for a wide array of applications.
Top Page Image Contents