Mitsubishi Electronics EX200U user manual Shock

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu- lated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUT- LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

Use the attached RGB cable with this equipment so as to keep interfer- ence within the limits of an FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

Not for use in a computer room as defined in the Standard for the Pro- tection of Electronic Computer/Data Processing Equipment, ANSI/ NFPA 75.

The attached power cord is to be used exclusively for this product. Never use it for other products.

When using the projector in Europe:

COMPLIANCE NOTICE

This Projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Direc- tive".

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system.

WARNING

Use the attached RGB cable with this equipment so as to keep interfer- ence within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

Note: This symbol mark is for

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality

EU countries only.

materials and components which can be recycled and/or reused.

This symbol mark is according to

This symbol means that electrical and electronic equipment, batteries and accumula-

the directive 2002/96/EC Article

tors, at their end-of-life, should be disposed of separately from your household waste.

10 Information for users and

If a chemical symbol is printed beneath the symbol shown above, this chemical sym-

Annex IV, and/or to the directive

bol means that the battery or accumulator contains a heavy metal at a certain concen-

2006/66/EC Article 20 Informa-

tration. This will be indicated as follows:

tion for end-users and Annex II.

Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)

 

In the European Union there are separate collection systems for used electrical and

 

electronic products, batteries and accumulators.

 

Please, dispose of this equipment, batteries and accumulators correctly at your local

 

community waste collection/recycling centre.

 

Please, help us to conserve the environment we live in!

 

 

EN-2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents EX200U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockControls and functions ProjectorRemote control Magnifying and searching for details on page 24 forRemote control effective range Obtaining a preferred projected image size Positioning your projectorChoosing a location EN-12 Layout of the projector Front projectionConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a monitorConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus If you forget the password Utilizing the password functionSetting a password Entering the password recall procedureSwitching input signal Disabling the password functionAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioSetting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementHow to use the Timer On key? Setting the presentation timerTo cancel the timer, perform the following steps Locking control keys Adjusting the soundHiding the image Freezing the imageShutting down the projector Direct power offPersonalizing the projector menu display Menu operation Menu systemSystem Setup Blank Timer Description of each menu DescriptionSetting Brightness Contrast Color System Setup Basic menu System Setup Advanced menu Change password EN-38 Maintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Spare lamp for EX200U VLT-EX240LPResetting the lamp timer Indicators Light Status & Description Power Temp Lamp Power eventsTroubleshooting Specifications Projector specificationsDimensions Timing chartReplacement part Supported timing for Component-YPbPrinputEN-49 Mitsubishi Electric Corporation
Related manuals
Manual 49 pages 20.98 Kb

EX200U specifications

The Mitsubishi Electronics EX200U and ES200U are innovative and highly efficient solutions designed to meet the demands of modern automation and control systems. Tailored for both industrial and commercial applications, these servo drives enhance performance while ensuring reliability and precision.

At the core of the EX200U and ES200U models is advanced motion control technology. These servo drives leverage high-resolution feedback systems to deliver exceptional positioning accuracy, which is critical in applications such as robotics, CNC machinery, and advanced manufacturing processes. The integration of Mitsubishi’s proprietary algorithms allows for real-time processing of motion commands, enabling smoother operations and reducing mechanical stress.

One of the standout features of the EX200U and ES200U is their versatility. These servo drives support a wide range of motor types, including synchronous and asynchronous motors, making them suitable for various operational demands. With scalable performance, users can easily adjust settings to match the specific needs of their applications, whether they require high speed or high torque.

Energy efficiency is another essential characteristic of the EX200U and ES200U. Both models are designed to minimize energy consumption without sacrificing performance. The incorporation of regenerative braking technology allows for energy to be recaptured during deceleration, contributing to lower operational costs and a smaller environmental footprint.

The user-friendly interface of the EX200U and ES200U simplifies configuration and monitoring. With intuitive software tools, engineers can quickly set up, program, and fine-tune the drives. The ability to interface seamlessly with Mitsubishi’s broader automation ecosystem enhances operational cohesion, allowing for standardized control and data analytics across multiple devices.

Safety is also prioritized in the design of the EX200U and ES200U. These servo drives come equipped with integrated safety features, including safe torque off and error handling capabilities that protect both equipment and personnel. Compliance with international safety standards further reinforces their reliability in industrial environments.

In summary, the Mitsubishi Electronics EX200U and ES200U servo drives represent a blend of advanced technology, user-centric design, and energy efficiency. With their impressive features and capabilities, they are well-equipped to handle the demands of contemporary automation, providing users with reliable and precise control for a wide array of applications.
Top Page Image Contents