PLUS Vision U7-132/U7-137 user manual Replacing the Lamp Cartridge

Page 61

Replacing the Lamp Cartridge

•The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors.

Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company.)

•When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the replacement following the procedure below.

•If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode and no longer turns on.

•Contact a store that sells the U7-132/U7-137 for a replacement lamp. Indicate you need a U7-300 replacement lamp for the U7-132/U7-137 (order code 28-057).

CAUTION

•Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop, disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will cause burns because of the high temperature.

•Do not remove any screws other than those specified.

•Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.

•If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store the projector was purchased.

E-61

Image 61

Contents U7-132/U7-137 DOC Compliance Notice PrecautionsPower Supply InstallationCleaning Lamp ReplacementMajor Features Table of Contents Table of Contents Adjustments and SettingsMenu Operations MiscellaneousRGB signal cable Mini D-sub 15-pin, 2 m / 6.6 feet Checking the Supplied AccessoriesDVI/Mini D-Sub 15-pin conversion adapter 18 cm / 0.59 feet Video cable RCA pin plug, 2 m / 6.6 feetStorage case for projector and accessories Checking the Supplied AccessoriesUSB cable type A, 2 m / 6.6 feet Cable pocketBuilt-in Security Slot Names of the Main Unit PartsNames of the Main Unit Parts Precautions Handling of the Remote Control Names of the Remote Control PartsRemote Control Range Preparing the Remote ControlInserting the Batteries Procedure Up to Projecting to the Screen Screen Size and Projection Distance Placement GuideConnections with Personal Computer Personal Computers with a DVI ConnectorDVI-D cable Available as an option. Order code Connecting Personal Computers and Video Equipment Personal Computers with a Mini D-Sub 15-Pin ConnectorRGB signal cable Supplied item Manufacturer Model Key To Output the External Output Signal of a Notebook ComputerVideo Equipment with Video Connectors Connections with Composite SignalsVideo Equipment with S-VIDEO Connectors Video cable Suppled item Video cable Supplied itemConnections with Component Signals Audio cable Supplied item Connections with Audio ConnectorsAudio conversion adapter Supplied itemConnections with the RGB OUT Connector Operating Switch on the projector powerButton on main unit Press the Enter button to set Power Cable Connections and Switching the Power On/OffThis completes the selection of the display language CursorFinishing Unplug the power cableAdjustment of the Projection Screen Adjustment of the Projection ScreenAdjust the projection image to the screen Zoom ringFocus ring Making Adjustments with the AdjustersRaising the projection image Lowering the projection imageGeneral Operation Automatic Adjustment of Analog RGBInput Selection Adjustment of the Volume Cancelling Video and Audio TemporarilyPress the Cancel button to immediately close the display Freezing a Moving PictureImage can also be moved in the following circumstances Enlargement of the Image and Video MovementPress the Zoom button to enlarge the image Using the Presentation Timer Operation Using the Laser PointerClick button on back Connecting the computer and projectorJOG buttons Click buttonControlling the Projector from a Computer Connecting via a LAN U7-137 onlyRS-232C connections CN-2 D-Sub 9-pin sideProtecting the Projector with the Security Lock Canceling the password/Changing the password Input the password using the number buttons 1 toCanceling the password Changing the passwordContent of Adjustments and Settings Using the Quick MenuPress the Select or button to adjust VolumeNames and Functions of Buttons Used for Menu Operations Menu Operation MethodAdjustment Bar Adjustment Bar and Settings ContentsMenu Screen Names and Functions Menu Operation MethodMenu Display Press the Menu button to display the menu Performing Menu OperationsSub menu Making Adjustments/SettingsSelecting Another Menu Name with Remote Control Operation RGB Terminal Menu name Item Name Sub Menu SetupImage Picture Adj. Picture AdjustmentBrightness / Contrast / Color / Tint / Sharpness Picture Adj. / Fine Picture / H Position / V PositionFine Picture ResetPosition ImageColor Select the preset color modeQuick Color Adj GammaColor Temp Selection contents at the time of YPbPr inputWhite Color SpaceWhite Balance Video Signals Personal Computer SignalView AspectKeystone Vertical Flip / Horizontal FlipKeystone Save ViewAuto Power Off SetupAuto Source Menu PositionSetup Lamp ModeStatus Indicator Input FormatTo start the timer Presentation TimerLanguage OptionOn Screen BackgroundStartup Screen Network PasswordSecurity Lock OptionLamp Timer Reset Factory DefaultInfo StatusLamp Timer Resolution / FrequencyInfo Indicator status What you should do When an Indicator is Lit or Blinking Thermal Protector Check the following matters before requesting servicing TroubleshootingCleaning a Soiled Projector Main Unit CleaningCleaning the Inside of the Projector Dirty LensReplacing the Lamp Cartridge Remove the lamp cartridge Replacing the Lamp CartridgeMount the new lamp cartridge Reset the Lamp TimerMount the lamp cover Optical SpecificationsElectrical MechanicalResolution Frequency Video SignalTable of Supported Frequencies Digital AnalogCabinet Dimensions 2005