Pioneer PDA-5002 Operations, Selecting an Input Source, Before you begin, make sure you have

Page 16

Operations

English

Operations

Selecting an Input Source

This section explains the basic operation of the plasma display. Outlined on the following pages is how to turn the main power on and off, put this display in the operation or standby mode and how to select connected components.

Before you begin, make sure you have:

•Made connections between the plasma display and AV components or personal computer as described in the section “Installation and Connections” starting on page 6.

•Set up the on-screen menu to input signals from components connected to INPUT1, INPUT2 and INPUT5 as described in the section “Setting Up the System” on page 14.

If no connections are made to these terminals, on-screen setup is not necessary.

2,5

2,5

3

3

4

Display Operating

Remote Control Unit

Panel

 

1Switch MAIN POWER on the display to the on position to turn the main power on.

The STANDBY/ON indicator lights red.

2Press STANDBY/ON to put the plasma display in the operation mode.

The STANDBY/ON indicator turns green.

16

3Press INPUT on the remote control unit or the display to select the input.

Input changes each time the display’s INPUT is

pressed as follows.

3 INPUT1 3 INPUT2 3 INPUT3

INPUT5 2

 

INPUT4 2

 

 

 

•When the menu screen is displayed, changing the signal input will cause the menu screen to turn off.

•If the input computer signal is not supported by the display, the following message will be displayed:

I N P U T 1

CA U T I O N

UN S UP P O RT E D S I G N AL

f H : 7 7 . 1 k H z

f V : 8 5 . 0 H z 1 1 5 2 X 8 6 4

F U L L

I N P U T 1

CA U T I O N

OU T OF R AN G E

f H : 7 5 . 7 k H z

f V : 1 2 0 . 0 H z

– – – –

F U L L

4Use VOLUME +/– on the remote control unit to adjust the volume.

If no audio connections are made to the plasma display, this step is not necessary.

5When viewing is finished, press STANDBY/ON to put the display in standby mode.

The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red).

6Switch MAIN POWER on the display to the off position to turn the main power off.

The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently.

CAUTION

Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as “screen burn” which leaves a ghost, or residual, image of the picture on the screen.

En

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PDA-5002 Contents Before ProceedingChecking Supplied Accessories Label for remote control unit BNC/Pin conversion adaptorPress 5/∞/2/3 to adjust the value Press Menu to display the menu screenPart Names and Functions Connection PanelPlasma Display Section Do not Make ANY Connections to this TerminalVideo Card PDA-5002 Section = AC InletInstalling the Video Card Installation and ConnectionsInstallation Input Connectors on the Plasma Display with Video Card Connection to INPUT1 and INPUT2Connection to AV component that has Component video jacks Connection to AV componentsConnection of G on Sync analog RGB source Connection of composite Sync analog RGB Source Connection to a personal computerConnection of separate Sync analog RGB Source Connections When connecting to INPUT1 When connecting to Output INPUT1Connection to INPUT3 Connection to INPUT4Connection to INPUT5 About DTV Set Top Box ConnectionAudio Connections Audio connection for component connected toINPUT3 INPUT4How to Route Cables Organize cables together using the provided speed clampsTo attach the speed clamps to the display To remove speed clampsSetting Up the System Setup after ConnectionSetting the Screen Mode / Input Signal Format Video SignalClamp Position setup Setup of Clamp PositionPress 5/∞ to select Clamp Position Press SET to select LockedOperations Selecting an Input SourceBefore you begin, make sure you have OperationsTo adjust the volume Press Volume on the remote control unitPress Muting on the remote control unit Press Display on the remote control unitDuring video signal input Screen Size SelectionChanging the screen size Automatic screen sizePartial Image Enlargement Point ZoomTo return to operating mode Automatic Power OFFPower OFF Adjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Display Panel Adjustments Press 2/3 to select ScreenPress 2/3 to carry out the adjustment To reset Screen mode settings to the defaultPress 2/3 to select YES, and press SET Rewriting the Input Display Other OperationsInput Label Changing the Color Temperature Color TempSetting the PureCinema mode Setting the Regional TV System FormatPress 5/∞ to select Purecinema Press 5/∞ to select Color SystemViewing a Fast Moving Picture 3D Y/C Mode Press SET repeatedly until the appropriate setting appearsPress 5/∞ to select 3D Y/C Mode Press SET to set the mode to MotionPress SET to set the mode to on Viewing in a Bright LocationHigh Contrast Press 5/∞ to select High ContrastPress Menu Auto FunctionPress 2/3 to select Option Audio Output Audio OUT Specifications AccessoriesAdditional Information GeneralPC signal compatibilty table INPUT5 Additional Information Video signal compatibilty table INPUT1, INPUT2Supplement Explanation of Terms

PDA-5002 specifications

The Pioneer PDA-5002 is a hallmark of modern audio technology, designed for enthusiasts who seek high-quality sound and versatile performance in their vehicles. This advanced digital amplifier integrates innovation and functionality to enhance the driving experience, making it a popular choice among car audio aficionados.

At the heart of the PDA-5002 is its powerful Class D amplifier architecture. This technology not only provides high efficiency, reducing the load on your vehicle’s electrical system, but it also ensures minimal heat generation, allowing for continuous use without the risk of overheating. With a maximum output power of 500 watts, the PDA-5002 delivers an impressive audio performance, capable of driving multiple speakers while maintaining clarity and dynamic range.

One of the key features of the PDA-5002 is its multi-channel configuration. It includes four channels, allowing users to connect a wide range of speaker setups, from simple front and rear speakers to more complex multi-speaker arrangements. This versatility makes the amplifier ideal for both casual listeners and serious audiophiles who demand high fidelity.

The unit supports a variety of audio signal inputs, including RCA and speaker-level inputs, ensuring compatibility with numerous head units and aftermarket systems. This flexibility is essential for users looking to upgrade their audio without overhauling their entire system.

Pioneer has also incorporated advanced signal processing technologies into the PDA-5002. Features such as adjustable crossover settings allow users to tailor the amplifier’s output to match their specific speakers and personal preferences. Bass boost and high-pass filter settings further enhance the audio experience, enabling users to achieve the perfect sound profile.

Durability is another hallmark of the PDA-5002. Built with robust components and a compact, heat-resistant chassis, it is designed to withstand the rigors of automotive environments, ensuring longevity and reliable performance. Its sleek design allows for easy installation in tight spaces, making it a practical choice for various vehicle models.

In summary, the Pioneer PDA-5002 stands out with its powerful Class D amplification, multi-channel capability, versatile input options, advanced signal processing features, and durable construction. It represents a perfect fusion of innovation and performance, catering to those who seek an enhanced listening experience on the road. For anyone looking to elevate their car audio system, the PDA-5002 is certainly worth considering.
Top Page Image Contents