
■The on-screen menus don’t appear
On your TV, make sure that the video input to which — the AV receiver is connected is selected.
When the AV receiver doesn’t connect TV with | — |
HDMI, onscreen menus are not displayed. |
|
|
|
Tuner
■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light
Relocate your antenna. | — |
Move the AV receiver away from your TV or | — |
computer. |
|
Listen to the station in mono. | 21 |
|
|
When listening to an AM station, operating the | — |
remote controller may cause noise. |
|
Passing cars and airplanes can cause interference. | — |
|
|
Concrete walls weaken radio signals. | — |
If nothing improves the reception, install an outdoor | — |
antenna. |
|
Remote Controller
■The remote controller doesn’t work
Before operating this unit, be sure to press | — |
RECEIVER. |
|
|
|
Make sure that the batteries are installed with the | 4 |
correct polarity. |
|
Install new batteries. Don’t mix different types of | 4 |
batteries, or old and new batteries. |
|
|
|
Make sure that the remote controller is not too far | 4 |
away from the AV receiver, and that there’s no |
|
obstruction between the remote controller and the |
|
AV receiver’s remote control sensor. |
|
Make sure that the AV receiver is not subjected to | — |
direct sunshine or |
|
Relocate if necessary. |
|
|
|
If the AV receiver is installed in a rack or cabinet | — |
with |
|
not work reliably when the doors are closed. |
|
Make sure you’ve selected the correct remote | 9, 41 |
controller mode. |
|
|
|
Make sure you’ve entered the correct remote control | 40 |
code. |
|
Make sure to set the same ID on both the AV | 34 |
receiver and remote controller. |
|
■ Can’t control other components
If it’s an Onkyo component, make sure that the u | 15 |
cable and analog audio cable are connected properly. |
|
Connecting only an ucable won’t work. |
|
|
|
Make sure you’ve selected the correct remote | 9, 41 |
controller mode. |
|
If you’ve connected a cassette tape deck, to the | 27 |
TV/CD IN jack, or an RI Dock to the TV/CD IN or |
|
GAME IN or VCR/DVR IN jacks, for the remote |
|
controller to work properly, you must set the display. |
|
|
|
If you cannot operate it, you will need to enter the | 40 |
appropriate remote control code. |
|
|
|
To control an Onkyo component that’s connected | 40 |
via u, point the remote controller at the AV |
|
receiver. Be sure to enter the appropriate remote |
|
control code first. |
|
|
|
To control an Onkyo component that’s not | 40 |
connected via upoint the remote controller at the |
|
component. Be sure to enter the appropriate remote |
|
control code first. |
|
|
|
Recording
■ Can’t record
On your recorder, make sure the correct input is | — |
selected. |
|
|
|
To prevent signal loops and damage to the AV | — |
receiver, input signals are not fed through to outputs |
|
with the same name (e.g., VCR/DVR IN to |
|
VCR/DVR OUT). |
|
|
|
USB Device Playback
■Can’t access the music files on a USB device
Make sure the USB device is plugged in properly. | — |
The AV receiver supports USB devices that support | 48 |
the USB mass storage device class. However, |
|
playback may not be possible with some USB |
|
devices even if they conform to the USB mass |
|
storage device class. |
|
USB memory devices with security functions cannot | 20 |
be played. |
|
Others
■Standby power consumption
In the following cases, the power consumption may 35 reach up to a maximum of 31 W:
–“HDMI Ctrl (RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter Standby mode as usual.)
■The sound changes when I connect my headphones
When a pair of headphones is connected, the | — |
listening mode is set to Stereo, unless it’s already set |
|
to Stereo, Mono, or Direct. |
|
■How do I change the language of a multiplex source
Use the “Input Ch (Mux)” setting on the “Audio | 32 |
Adjust” menu to select “Main” or “Sub”. |
|
■The ufunctions don’t work
To use u, you must make an uconnection and 15 an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.
En
45