InFocus TD40 PAL manual FCC Notice

Page 4

Caution

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK),

NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

CAUTION

-TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD.

-DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

-SHOCK HAZARD DO NOT OPEN.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

CAUTION

The stand is intended for use with this monitor only. Use with other products may result in injury.

WARNING

-Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

-This is Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

-To reduce the risk of fire and electric shock, do not expose this product to rain or moisture.

FCC NOTICE

This device has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in home environment as well as in a commercial, industrial or business environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Connecting of peripherals requires the use of grounded shielded signal cables.

Always be careful when using your the Monitor. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine.

Read all safety and operating instructions before operating your the Monitor.

Keep the safety and operating instructions for future reference.

Heed all warnings on the Monitor and in the operating instructions.

OWNER'S MANUAL 3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents USER’S Guide Contents Setting the Picture FCC Notice Page Important Safety Information Follow all operating and use instructionsImportant Safety Information Important Safety Information Only use the specified batteries Accessories Viewing the Control PanelOSD Key Position OSD Key FunctionViewing the Connecting Panel Back Panel and JacksRS-232C Configurations RGB PC Input Jack D-SUBViewing the Remote Control Key DescriptionTTX / program Edit keys PIP Picture In Picture KeysLeft Up Reception range of remote control Loading the BatteriesInstallation Table Stand Installation optionalSpeaker Installation optional Speaker AccessoriesConnecting the TV Cable Connecting the TV CableConnecting the VCR Connecting the VCRWatching VCR Connecting the DVD Connecting the DVDHow to use Component Input portsConnecting the Set Top Box How to connectSupported Signals With ComponentConnecting the PCD-Sub & DVI Connecting a PC to the MonitorPin Configuration Pin NoDisplayable Monitor Specification Vertical Frequency HzVolume Control Basic OperationTurning the Monitor On And Off Select SourceOSD Menu Structure Example of OSD MenuMain Menu Sub MenuSetting the Channel Auto ScanAuto Scan Supported countries are shown as belowAuto Scan Other Countries NationManual Scan Fine TuneEdit Edit Favorite program ListDigest Function DigestTeletext On / Mix / Off TOP textUser mode has additional settings in a sub-menu See next Setting the PictureMode Adjust User Mode Select User mode PreviousContrast Temperature Cool 1Normal Warm 1Setting the Picutre Video NRScreen Format Video NRPanorama Screen Format Description WideZoom Setting the Picture PC GeometryPosition Phase Sound Mode Setting the SoundBalance AVC Auto Volume Control User AdjustSpatial Effect MTS Multichannel Telersion SoundTranslucent Setting the OthersPIP Picture In Picture Size in PIP Picture In Picture Source in PIPPicture Swap in PIP Picture In Picture Position in PIPAdvanced Set ID in AdvancedLanguage in Advanced Blue Back in AdvancedFront key Lock in Advanced Time Set Setting the TimeOn Time Available only when the Time is set and On Time is on On VolumeOn Channel Off Time SleepTroubleshooting Problem Quick Action for Possible SolutionWarranty Card Limited WarrantyTo Be Eligible For Limited Warranty Coverage Limited Warranty PeriodTo Obtain Warranty Service Memo
Top Page Image Contents