JVC DLA-HD100 manual English, Do not allow any unqualified person to install the unit

Page 3

-To allow better heat dissipation, keep a clearance between this unit and its surrounding as shown below. When this unit is enclosed in a space of dimensions as shown below, use an air-conditioner so that the internal and external temperatures are the same.

 

150 mm and above

300 mm

300 mm

and above

and above

150 mm

 

and above

200 mm

 

 

and above

-This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

-This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.

-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.

-For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges.

-Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock.

-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

-Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel.

-Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions:

a)When the power supply cord or plug is damaged.

b)If liquid has been spilled, or objects have fallen on the product.

c)If the product has been exposed to rain or water.

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the Operation Manual, as an improper adjustment of controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e)If the product has been dropped or damaged in any way.

f)When the product exhibits a distinct change in performance - this indicates a need for service.

-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

ENGLISH

-Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

-The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat.

-When connecting other products such as VCR’s, and DVD players, you should turn off the power of this product for protection against electric shock.

-Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that present special hazards when over heated.

-Do not look into the projection lens while the illumination lamp is turned on. Exposure of your eyes to the strong light can result in impaired eyesight.

-Do not look into the inside of this unit through vents (ventilation holes), etc. Do not look at the illumination lamp directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired.

-Do not drop, hit, or damage the light-source lamp (lamp unit) in any way. It may cause the light-source lamp to break and lead to injuries. Do not use a damaged light source lamp. If the light-source lamp is broken, ask your dealer to repair it. Fragments from a broken light-source lamp may cause injuries.

-The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the lightsource lamp. If anything is unclear, please consult your dealer.

-Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury.

-Use only the accessory cord designed for this product to prevent shock.

*DO NOT allow any unqualified person to install the unit.

Be sure to ask your dealer to install the unit (e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation is performed by an unqualified person, it may cause personal injury or electrical shock.

Getting Started

Preparation

Basic Operation

Settings

Troubleshooting

Others

3

Image 3
Contents For Customer use Pour utilisation par le clientInstrucción para el cliente About the installation place Safety PrecautionsEnglish Do not allow any unqualified person to install the unitSafety Precautions Preparation Basic Operation Settings Troubleshooting Others Supports Multiple Digital Devices Main FeaturesPerfect for Any Location Contents About this Manual How to Read this Manual/ Accessories/Optional AccessoriesCheck the Accessories Optional AccessoriesControls and Features „ Front Side/Left Side„Rear Side/Top Surface „Bottom Surface „ Remote Control Controls and FeaturesHow to Use the Remote Control Effective Range of Remote Control UnitLoading Batteries DVD Recorder DVD Player Selecting Connecting DevicesConnecting Connecting via Video Cable and S-video CableConnecting via Component Video Cable Connecting via Hdmi Cable Connecting via HDMI-DVI Conversion CableDVD recorder Device equipped with RGB output Connecting via SCART-RCA CableConnecting via RGB Video Cable DVD player for European marketInstall the projector and screen Installing the Projector and ScreenTips Screen Size and Projection DistanceProjecting Image Insert the power plug to the power outletTurn off the power About Cool Down modeYou can hide the image Temporarily Masking the Surrounding Area of an Image Convenient Features during ProjectionSetting the Screen Size Project the imageTo end Mask the imageSelect Source g Aspect Setting MenuDisplay the setting menu Procedures for Menu OperationSetting Menu Image Image AdjustImage Color Temp Gamma Image GammaImage Offset Image Pixel AdjustSetup Image Profile Setup Profile MemorySetup Overscan Setup Picture PositionSetup Hdmi Input Level Setup MaskSource Film Mode Source Aspect When SD video signals are being inputSource V-Stretch When HD video signals are being input Source Resize When PC signals are being inputSource Black Level Install. Menu PositionInstall. Menu Display Source Color SystemInstall. High Altitude Mode Install. Line DisplayInstall. Flip H Install. FlipFunc. Lamp Power Func. LogoFunc. Test Pattern Info. During video signal input Customizing Projected Images Adjust image qualityOther items can also be adjusted To end Changing the Default Image Profile ValuesRegister the setting Adjust image qualityDisplay the setting menu Select Setup g Profile Memory g Save User1Video image does not appear TroubleshootingPower is not supplied Projected image is darkVideo images are missing Remote control does not workPower is cut off suddenly Video image is fuzzyMessage Cause Details What to Do When These Messages Are DisplayedAbout Warning Indicators Actions to Be Taken for Warning ModeLamp Loosen the screws on the lamp unit Procedure for Lamp ReplacementReplacing the Lamp Remove the lamp coverAfter Replacing the Lamp Attach the lamp coverResetting Lamp Time Reset lamp timeIf the filter is damaged or too Dirty to be cleaned Cleaning and Replacing the FilterClean the filter Reinstall the inner filterGND RS-232C SpecificationsCommand Format RS-232C InterfaceVideo Comp VideoRS-232C Interface Dynamic MenuCinema NaturalThis section shows the communication examples of RS-232C RS-232C Communication ExamplesAcquired About Trademarks and Copyright Copyright and CautionMounting this Unit Precautions for MountingSpecifications DLA-HD100Component Dimensions „ Top Surface„ Bottom Surface Memo 1007TTH-SW-VP