JVC Model DLA-HX1E manual Capture start, Options menu, Color profile menu, Language menu

Page 39

Adjustments and Settings Using Menus

p“Capture start”

The status of capture is displayed in bold.

“Capt. in prog. (approx. 2min)” The image is being read into the projec- tor. During this time interval, the projec- tor will not respond to any command sig- nal inputted by the user.

“Signal can not be captured” Clear the message with the [EXIT] but- ton and input appropriate signals.

“Reduce capt. size”Clear the message with the [EXIT] but- ton and decrease the signal size.

Depending on the image content, there will be cases where certain sig- nals cannot be captured while others of the same size can be.

q“Options” menu (“Page 1”)

The items of the “Options” menu shown below can be adjusted.

• The “Options” menu consists of two pages (“Page 1” and “Page 2”).

“Page 1”

Adjustment item (press  / )

Adjustment content (press  / )

“Color profile”

Sets the color table.

 

 

[ Press the [ENTER] button to enter the

 

“Color profile” menu w.

 

“Menu display”

Sets whether the menu display automati-

 

cally clears after 15 seconds.

 

 

Values : “15sec”, “ON”

{“15sec”}

 

 

“Line display”

Sets whether the line display is shown for

 

about 5 seconds.

 

 

Values : “5sec”, “OFF”

{“5sec”}

 

 

 

“Flip H”

Reverses image left to right.

 

 

Values : “ON”, “OFF”

{“OFF”}

 

 

 

“Flip V”

Inverses image upside down.

 

 

Values : “ON”, “OFF”

{“OFF”}

 

 

“Page 2”

Displays “Page 2” of the “Options” menu.

 

[ Press the [ENTER] button to enter the

 

“Options” menu (“Page 2”) e.

w“Color profile” menu

To choose the color table of the image signals, press the ( / ) CUR- SOR buttons. When using “Color profile”, set the “Color temp.” to “6500”.

No display in the absence of image signal input. Values : “------”, “HDTV”, “MacRGB”, “NTSC”, “PAL”

{“------”}

e“Options” menu (“Page 2”)

Adjustment item (press  / )

Adjustment content (press  / )

“Sleep time[min]”

Sets the length of sleep time which, when

 

lapsed, automatically puts the projector

 

into stand-by state if no signal is input-

 

ted.

 

 

Setting value: “15”, “30”, “60”, “OFF”

 

 

{“OFF”}

“Menu color”

When “ON”, menu becomes transparent

 

and the background can be seen through

 

it.

 

 

Setting value: “OFF”, “ON”

{“OFF”}

 

 

“PC2(BNC)”

Sets whether to use the BNC connector

 

on the back of the projector as an “RGB”

 

signal input terminal or as a “YPBPR

 

(color-difference) signal input terminal.

 

Please reset it based on the connected

 

apparatus.

 

 

• The input will be “RGB” irrespective

 

of the PC signal setting.

 

 

Setting value: “RGB”, “YPbPr

{“YPbPr”}

 

 

“DIST”

Image of high resolution can be achieved.

 

Set as required.

 

 

This is turned “ON” when the [OPERATE]

 

button is pressed.

 

 

Setting value: “OFF”, “ON”

{“ON”}

 

 

“SCART”

Connects to a Europe-adapted SCART

 

plug and turns it “ON” during component

 

input.

 

 

Connect the Image Signal cable to the

 

[RGB] terminal of the [PC2] input termi-

 

nal and the Sync Signal cable to the

 

[VIDEO IN] terminal.

 

 

Setting value: “OFF”, “ON”

{“OFF”}

“RS-232C [bps]”

Sets the communication speed (signal

 

transmission speed) when communicat-

 

ing with a computer by using the [RS-

 

232C] terminal. Please set the baud rate

 

for transmission.

 

 

Setting value: “9600”, “19200”

{19200}

“SXGA”

Select “1400” to project SXGA+ signal.

 

Setting value: “1280”, “1400”

{1280}

 

 

“PC 3”

Set whether to use PC input or HDCP

 

compatible video signal when using [PC3]

 

terminal as input. Set according to the

 

connecting equipment.

 

 

Setting value : “PC”, “HDCP”

{“HDCP”}

 

 

 

r“Language” menu

Select the language in this language menu with the CURSOR buttons ( / ).

Setting value : [] (Japanese), [English], [Deutsch] (German), [Español] (Spanish), [Italiano] (Italian), [Français]

(French), [Português] (Portuguese) and [] (Korean).

{[English]}

Some words in the menu and proper nouns such as “VIDEO”, “NTSC”, “QUICK ALIGN...” are shown only in English.

39

Image 39
Contents Model No. DLA-HX1U Serial No For customer UseMachine Noise Information Germany only FCC Information U.S.A. onlyFor United For European Kingdom Safety PrecautionDo not allow any unqualified person to install the unit Power supply voltage AC 120Do not cut off the main plug from this equipment How To Replace The FuseAbout burning-in of the D-ILA device Using the projectorHow to use the Screen Trigger terminal cable Using the screen mode switch functionAccessories ContentsFront Side/ Top Surface/ Left Side Controls and FeaturesRear Side/ Right Side/ Bottom Surface Controls and FeaturesConnector Panel Control Panel on the Projector Indicator Display on the Control PanelTemp Indicator Stand by IndicatorOperate Indicator Lamp IndicatorFocus button Not functional on this unit Remote Control UnitVolume button Video button PC buttonDigital Zoom ª / · buttons Remote Control’s signal transmitter Operate buttonVolume ª / · button Screen „ / Í buttonLoad the batteries Loading Batteries into the Remote ControlPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorMounting the Projector Installing the Projector against the ScreenInstalling the Projector Precaution for ceiling-mountScreen installation Projection Distance and Screen Size43 Screen When the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit  Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector  Video signals Allowable input signals Connecting to Various DevicesConnection Connecting to Devices Connecting to Video Devices Right side of projector Connecting to Computers Connection for controlling more than one projector  Control from external device When using the projector, remove the Lens Cap Connecting the Power Cord suppliedBasic Operations Basic Operation ProceduresPower On Insert the power cord into the wall outletBasic Operations  Display using the direct buttonsAdjusting the Zoom Ring the screen size Adjusting the Focus Ring FocusPlug out the power cord from wall outlet Adjusting the Sound VolumePower Off Press Volume · 50Enlarging the Image Frequently used Convenient FunctionsDisplaying a Still Picture Turning Off Image and SoundRemoving the Trapezoidal Distortion of the Image  Vert.keystone Display Horiz.Keystone Display Using the Quick Alignment function Press the Quick ALIGN. Quick Alignment buttonQuick Alignment function Submenu Adjustments and Settings Using MenusMenu Structure Main menuMain menu Submenu Adjustments and Settings Using MenusMain Set up menu When PC input is selected Main Set up menu When video input is selectedMenu Operation Buttons MenuButton Procedure for Menu Operation Image adj. menu Adjustment and Setting Using MenusMenu Configuration Set up menuResize menu Position menuAspect ratio menu Decoder menuLanguage menu Capture startOptions menu Color profile menuInformation menu Setting Aspect ratio and Resize Setting the Aspect ratioProject the image onto the screen Optimum image Setting Aspect ratio and ResizePress the Menu button to end when adjustment is com- pleted Select Zoom with the cursor buttons  / Resize menu appears on the screen Setting the ResizeSet the Resize when Hdcp image is input from PC3 terminal Select Resize with the cursor buttons  /  and press EnterSet Resize to Zoom for optimum projected image Press the Enter or the right cursor button  Editing and Projecting LogoProject the images to be included in your logo Select Logo with the cursor buttons  / Editing and projecting logo Light source lamp and its lamp time Procedure for lamp replacementAbout lamp replacement Replacing the LampClose the handle, and tighten the screw Replacing the LampRemove the lamp unit Insert the new lamp unit until it is fullyPress for Resetting the lamp timeInsert the power cord into the wall outlet To ensure the lamp time has been resetReinstalling the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Clean the filterPlied TroubleshootingSymptom Probable cause Corrective action TroubleshootingMessage Cause Contents What to do when these messages are displayedWhat to do when these messages are displayed  Action to be taken upon warning indications  About warning indicatorsFor details on individually blinking indicators, please see Please follow the procedures belowPB, PR Specifications Bottom SpecificationsDimensions unit mm  Top  Front PC 3 terminal Pin number Signal namePin arrangement  Y/C terminal  RS-232C IN/OUT terminal  PC 1 terminalCommunication Specifications Command Format RS-232C external control External control command table Memo SW-VP