JVC GD V502U, GD-V422U manual AC cord connection, Optional Video Input Card insert Slots covered

Page 47

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

(Example: GD-V422PCE)

Speakers (Optional accessories)

SPEAKERS

Terminals (L)

1
2	1
	1
	2

	SPEAKERS	AC cord connection
	Terminals (R)	AC cord connection
	Terminals (R)	(see page 12)
		(see page 12)
		– AC cord fixing

Note: Connect the power cord before combining with accessories such as the Stand Unit. When combining with accessories such as the Stand Unit, be very careful not to pinch the power cord.

1. Open the clamper.	2. Insert the AC cord and
	close the clamper
	securely.

3.Slide up the clamper and fix the AC cord plug securely.

When loosen the clamper:

Clamper

AC cord

Note: The power plug in the illustration may not be the type fitted to your set.

– Cable fixing bands Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

1

2

To tighten:

To loosen:

Push the catch

Pull

Pull

Optional Video Input Card insert Slots (covered)

AUDIO

PC IN

SERIAL

SLOT1SLOT2

Note:

Insert the optional Video Input Cards before combining the Plasma Display with the Stand Unit.

SLOT3

From EXTERNAL monitor terminal on Computer (see page 8)

From SERIAL terminal on Computer

7

Image 47

Contents Instructions Plasma Display MonitorRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits Attach the ferrite coreIf problems occur during use Safety PrecautionsSet up AC Power Supply CordElectric shocks can result if this is not done Cleaning and maintenanceWhen using the Plasma Display All of the following accessories are manufactured by JVCRemote Control Batteries AccessoriesAccessories Supplied AC cord fixing ConnectionsSpeakers PC Input Terminals connection Signal Names for mini D-sub 15P ConnectorCommunication parameters Installing the ferrite core Large sizeCommand Serial Terminals connectionRGB signal R, G, B, HD, VD AC cord connection Power on / OFFPower on / OFF Connecting the AC plug to the Wall OutletViewing Basic ControlsNormal Surround button Press to accessOFF Timer button Stand-by on / OFF buttonAdvanced SettingsOn-Screen Menu Displays Duration / Saver Time / Power OFF TimeSelecting the On-Screen Menu Language Input Signal SelectionSelect the Input Signal Auto Just Mode Picture ExplanationAspect Controls Normal Zoom FullHelpful Hint N / Normalize Normalization Adjusting Picture POSITION/SIZEAdjusting screen Size / Clock PhaseMute Sound AdjustmentNormal Cool Warm Picture AdjustmentsAuto Standard Cinema Dynamic Advanced Settings Present Time Present Time SetupSetup SET UP TimerPower OFF Function SET UP TimerPower on TIME/POWER OFF Time Power OFF TimeNegative / Scroll selection Mode selectionStart setting Screensaver For preventing after-imagesPeak Limit Setup of Screensaver TimeReduces screen after-image Press to exit from Screensaver Side BAR AdjustOFF, DARK, MID, Bright OFF Dark MID Bright Select the magnification required for the enlarged display Digital ZoomDisplay the Operation Guide Select the area of the image to be enlargedCustomizing the Input labels Reduces power consumptionPress to display Multi Display Setup menu Press to select Setup for Multi DisplayHow to setup Multi Display Multi Display SetupNTSC, PAL, Secam Press to select 2×2, 3×33D Y / C Filter For Ntsc Video images SET UP for Input SignalsComponent / RGB in Select Component RGBIf the image becomes unstable Color System / Aspect AutoPulldown Displays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzCars / Motorcycles TroubleshootingPlasma Display panel Symptoms Check Electrical AppliancesPAL60 Video / Component / RGB / PC input signalsApplicable input signals for PC Input mini D-sub 15P ∗ Mark GD-V422U GD-V502U SpecificationsPage GD-V422U / GD-V502U Plasma Display Monitor Plasma Display Monitor GD-V422PCEINSTRUCTIONS GD-V502PCEPresent Time Setup Green-and-Yellow Earth Important Safety NoticeFor Your SAFETY, Please Read the Following Text Carefully This Apparatus Must be EarthedDo not remove the cover or modify it in any way SetupDo not stick any foreign objects into the Plasma Display Clean the power cable regularly to prevent it becoming dusty Requires two R6 batteries Accessories SupplyObserve the following precaution Optional Video Input Card insert Slots covered AC cord connectionSDA HD/SYNC SCL GND Ground Signal NameFull Just Norm ZoomButton see Picture button Main Power Button On / Off SwitchRemote control Menu Screen on / OFF Power Indicator Sensor Enter / AspectPicture POS./ Size button SET UP buttonOff Position buttons Digital Zoom see Sound button seePower On / Off and input signal selection Power On / Off and input signal selection To Sound adjust menu see To Picture adjust menu seePower OFF Time Press to access each adjust screen From the unitPress to Setup Power on TimeAuto ZoomJust Size Adjusting Picture Pos./ SizeHelpful Hint N / Normalise Normalisation PosCinema NormalDynamic Advanced settings Balance MuteBass TrebleExit Button Can be operated Mute button VOL buttonPresent Time Setup Present Time Setup / Set up TimerSet up Timer Screensaver under On, press the R button Reversal / Scroll selectionWhite bar scroll Image Reversal OffStart Time Finish Time Peak limitSide Panel Adjustment PC MiniD-sub input PC/COMPONENT/RGB/DVD/STB Power managementPress to exit from Setup Press to select the Multi Display Setup Press to select 2×2, 3×3 Component Setup for Input SignalsComponent / RGB-in Select 3D Y / C Filter For Ntsc AV imagesPAL Secam Ntsc Colour system / Aspect AutoCinema reality If the picture image becomes unstableSync No Picture No Sound By button on the remote control When Multi Screen Input signal can be displayedSignal name Horizontal Vertical Component GD-V422PCE GD-V502PCE GD-V422PCE / GD-V502PCE Plasma Display Monitor