JVC G1000 manual Left-hand side, AC in power input terminal, Main Power switch, Connector panel

Page 7

Controls and Features (cont.)

Left-hand side

p

q w

e

pAC IN (power input) terminal

This is the power input terminal where the supplied power cord is connected. For details, refer to page 24.

qMAIN POWER switch

This is the main power switch. When it is turned on, the projector goes into stand-by state, and the STAND BY indicator on the control panel comes on.

ON [ ❙ ]: The main power turns on.

OFF [à]: The main power turns off.

wConnector panel

For details, refer to “Connector Panel” on page 11.

eAdjustable foot (for horizontal angle adjustment)

It is set at the shortest position when shipped from the factory. Turn the foot to make the projector level. Adjustment can be made in the range of + 1.5° and – 1.5° from the horizontal position.

+1.5°

–1.5°

ENGLISH

Extend Shorten

7

G1000 [D] p.05-14

7

99.2.24, 5:50 PM

Page 6 Page 8
Image 7
Page 6 Page 8
Contents G1000 About burning-in of the D-ILA device Safety PrecautionsXenon gas is enclosed with high pressure inside the light Safety PrecautionsLighters that present special hazards when over heated Lamp is turned on. Exposure of your eyes to the strongContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesAdjustable foot for horizontal angle adjustment AC in power input terminalMain Power switch Connector panelOpening for replacing the light-source lamp Refer to Precautions for Installation onBottom Surface Air intake area filterControl Panel Computer button Setting buttonWhen a menu is shown Video buttonComputer OUT computer output terminal D-sub 3-row 15 pin Connector PanelC S video input terminal Mini DIN 4 pin RS-232C terminal D-sub 9 pinAudio audio input terminal stereo mini jack Input of external sync signals is automatically detectedAudio input terminal stereo mini jack Row 15 pinRemote Control Unit Open the back cover Installing BatteriesInstall the batteries Precautions for using batteriesWhen installing the projector, observe the followings Installing the ProjectorPrecautions for Installation Do not install the projector in the following placesProjection Projection Distance and Screen SizeProjection screen size diagonal length Center line of the lens65.6 ft 20.0 m 345 Approx cm 521 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 62.32 ft 19.0 m 328 Approx cm 495Effective range and distance of the remote control unit Effective Range and Distance of the Remote Control UnitUse the projector with A+B about 10 m 32.8 ft or less Computer signals Connecting to Various DevicesSignals that Can Be Input to the Projector Video signalsHi-Vision devices Connecting to Video DevicesConnecting to Hi-Vision Devices Video devicesTo Audio OUT Connecting to Other DevicesConnecting to Devices which Control the Projector Desktop typeRGB output devices To R Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer Read the manual which comes with each device thoroughlyConnection to Macintosh To monitor connector SuppliedPersonal computer connection cable To prevent fire and electric shock, observe the following Connecting the Power Cord SuppliedTo use the projector Remove the lens capWhen Turning On the Devices Connected to the Projector Changes to steady on Turning on the PowerTurn on the Main Power switch Basic OperationsFollows Adjust the screen sizeWhen you press Video When you press ComputerButtons Adjust focusAdjust sound volume Adjust focus with the remote control’s Focus +Press once To turn off video image and audio sound temporarilyTo use the quick alignment function Projector’s buttonTo display the Main menu Remote control unit To display the Setting menuTo use the remote control’s Preset button Projector buttonPress the Setting button to select the desired item Operating the Setting MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu To finish the main menu, press the page Back button Changing the Color SystemSelect Decoder with the cursor button 5 or Set the color system with the cursor button 2 orAbout language display Changing the Language DisplaySet the desired language with the cursor button 2 or Language displayAdjust Tracking and Phase with the cursor buttons Adjusting the Pixel ClockButton Adjustment content Adjust H. POS. and V. POS. with the cursor buttons Adjusting the Screen PositionSelect Position with the cursor button 5 or When computer-related signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or When AV signals are inputPicture menu Submenu itemsFor video system input For computer system input30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Sets a mode which allows easyAdjustment values 0, text 30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lowerButton 5 or Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Select the Sound with the cursorSelect the Options with the cursor button 5 or Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or Following optional functions can be set adjustedOptions menu Set adjust the desired item with the cursor button 2 orAspect Source item shown in text is indicated in magenta color Changing Setting the SourceSelect a submenu item Source using the cursor button 5 or Select the item to set using the cursor buttons 5/ or 2/3Submenu item When Auto is selectedWhen other than Auto is selected Press the MENU/ENTER button to set fix itLoosen the two screws with a flat-end screwdriver Replacing the Light-Source LampScrews Replace the lamp-replacementInsert the new lamp unit fully inside and fasten the screws Opening cover and fastenAt the same time for six seconds or more Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode Projector’s buttonReinstall the filter Cleaning and Replacing the FilterTurn off the Main Power switch Clean the filterTroubleshooting Maintenance AV in AV in input SpecificationsComputer in Computer input Other Front Outside dimensionsDTV-format signals TopComputer IN-1 PC / Computer OUT Terminal Pin assignment Specifications for terminalsTerminal RS-232C terminalG1000D p.46-59 99.2.24, 552 PM English
Top Page Image Contents