JVC G1000 manual Control Panel

Page 9

Controls and Features (cont.)

Control Panel

 

STAND BY

1

 

 

2

 

 

3

 

LAMP

4

 

TEMP

5

 

EMERGENCY

6

 

VIDEO

7

 

COMPUTER

8

 

SETTING

9

 

+3

 

 

QUICK

p

 

ALIGN.

 

-2

 

1 STAND BY Indicator

 

ON

: When in stand-by mode.

 

Blinking : When in cool-down mode.

 

Memo

About the cool-down mode:

This projector has a function to cool down the heated lamp for a fixed period of time after projection is finished. This feature is referred to as the cool-down mode.

CAUTION

•The purpose of the cool-down mode is to prevent inner parts from being deformed or broken by heat from the heated lamp as well as to prolong the life of the lamp. Do not turn off the main power switch while in the cool-down mode. Also, do not place the projector on its side or stand it upright; this may block the exhaust vents.

2OPERATE indicator

ON: When the projector is in operation (projecting)

3OPERATE button

4Lamp indicator

ON

: After the light-source lamp has been used for

 

more than approx. 900 hours.

Blinking : Replace the lamp. Refer to “Replacing the Light- Source Lamp” on page 48.

5TEMP indicator

ON: The temperature inside the projector has abnormally risen.

Note

•While the TEMP indicator is on (during abnormal temperature), the power is automatically cut off, and an emergency mode is shown (with the EMERGENCY indicator blinking).

6EMERGENCY indicator

Blinking: Something abnormal has occurred with the projector.

Memo

About the emergency mode:

The emergency mode is shown when the following anomalies have occurred with the projector (the EMERGENCY indicator blinks). In the emergency mode, projection is automatically interrupted and the cooling fans operate for about 20 seconds.

•When the air filter is displaced.

•When the filter is clogged.

•When the light-source lamp has suddenly gone off.

•When the fans have stopped.

•When the temperature inside has risen abnormally high.

CAUTION

• When an emergency mode is shown:

After the cooling fans have stopped, turn off the main power switch and unplug the power cord from the wall outlet. Make sure the lamp-replacement cover and the air filter are correctly installed. Then, plug in the power cord again and operate the projector.

If it goes into an emergency mode again, after the cooling fans have stopped, turn off the main power switch, unplug the power cord, and call your dealer for repair.

ENGLISH

When the projector is in the stand-by mode, press this button, and the main power switch is turned on, causing the OPERATE indicator to light. Press it again, and the projector goes into the cool-down mode, then stand-by mode.

Memo

While in the cool-down mode:

If you press the OPERATE button, the projector is not tuned on.

9

G1000 [D] p.05-14

9

99.2.24, 5:50 PM

Page 8 Page 10
Image 9
Page 8 Page 10
Contents G1000 About burning-in of the D-ILA device Safety PrecautionsLighters that present special hazards when over heated Safety PrecautionsLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the lightContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesMain Power switch AC in power input terminalConnector panel Adjustable foot for horizontal angle adjustmentBottom Surface Refer to Precautions for Installation onAir intake area filter Opening for replacing the light-source lampControl Panel When a menu is shown Setting buttonVideo button Computer buttonC S video input terminal Mini DIN 4 pin Connector PanelRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinAudio input terminal stereo mini jack Input of external sync signals is automatically detectedRow 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Install the batteries Installing BatteriesPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorDo not install the projector in the following places When installing the projector, observe the followingsProjection screen size diagonal length Projection Distance and Screen SizeCenter line of the lens Projection59.04 ft 18.0 m 311 Approx cm 469 55.76 ft 17.0 m 294 Approx cm 44362.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Effective Range and Distance of the Remote Control Unit Effective range and distance of the remote control unitUse the projector with A+B about 10 m 32.8 ft or less Signals that Can Be Input to the Projector Connecting to Various DevicesVideo signals Computer signalsConnecting to Hi-Vision Devices Connecting to Video DevicesVideo devices Hi-Vision devicesConnecting to Devices which Control the Projector Connecting to Other DevicesDesktop type To Audio OUTConnection to an IBM PC or IBM-compatible computer Connecting to Computer DevicesRead the manual which comes with each device thoroughly RGB output devices To RTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable To use the projector Connecting the Power Cord SuppliedRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turn on the Main Power switch Turning on the PowerBasic Operations Changes to steady onWhen you press Video Adjust the screen sizeWhen you press Computer FollowsAdjust sound volume Adjust focusAdjust focus with the remote control’s Focus + ButtonsTo use the quick alignment function To turn off video image and audio sound temporarilyProjector’s button Press onceTo use the remote control’s Preset button Remote control unit To display the Setting menuProjector button To display the Main menuMaking Basic Settings Operating the Setting MenuPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Select Decoder with the cursor button 5 or Changing the Color SystemSet the color system with the cursor button 2 or To finish the main menu, press the page Back buttonSet the desired language with the cursor button 2 or Changing the Language DisplayLanguage display About language displayAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or Select the item to adjust with the cursor button 5 or Adjusting Picture QualityWhen AV signals are input When computer-related signals are inputFor video system input Submenu itemsFor computer system input Picture menuAdjustment values 0, text Sets a mode which allows easy30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddishAdjust Treble and Bass with the cursor buttons Adjusting Sound QualitySelect the Sound with the cursor Button 5 orSelect the item to set adjust with the cursor button 5 or Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted Select the Options with the cursor button 5 orOptions menu Set adjust the desired item with the cursor button 2 orAspect Select a submenu item Source using the cursor button 5 or Changing Setting the SourceSelect the item to set using the cursor buttons 5/ or 2/3 Source item shown in text is indicated in magenta colorWhen other than Auto is selected When Auto is selectedPress the MENU/ENTER button to set fix it Submenu itemLoosen the two screws with a flat-end screwdriver Replacing the Light-Source LampInsert the new lamp unit fully inside and fasten the screws Replace the lamp-replacementOpening cover and fasten ScrewsTurn on the Main Power switch to go into stand-by mode Resetting the Lamp Use TimeProjector’s button At the same time for six seconds or moreTurn off the Main Power switch Cleaning and Replacing the FilterClean the filter Reinstall the filterTroubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other DTV-format signals Outside dimensionsTop FrontTerminal Pin assignment Specifications for terminalsRS-232C terminal Computer IN-1 PC / Computer OUT TerminalG1000D p.46-59 99.2.24, 552 PM English
Top Page Image Contents