Knoll Systems HDP6000 user manual ? No start up screen? Get help on, Remove the top front lid

Page 11

11

Computer connections

You can connect a computer‟s VGA connector to the VGA input on the projector using a VGA cable.

RS-232 connections

You can control the projector from an LCD control panel or computer by connecting an RS-232 cable to the projector‟s Serial control connector.

Displaying an image

Connect the power cord to the Power connector cord

plug in power

on the back of the projector and to your electrical outlet.

 

 

 

 

 

 

 

 

 

 

 

NOTE: Always use the power cord that shipped with the projector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the Power button on the remote control.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The LED blinks green and the fans start to run.

press power button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When the lamp comes on, the start-up screen is displayed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and the LED is steady green. It can take a minute for the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

image to achieve full brightness.

 

 

 

 

 

 

 

 

 

 

 

? No start up screen? Get help on page 13

 

 

 

 

 

 

 

 

 

 

 

Plug in, connect, and turn on your video device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The video device‟s image should appear on the

turn on video device

 

 

 

 

 

 

 

 

 

 

projection screen. If it doesn‟t, press the Source button

 

 

 

 

 

 

 

 

 

 

 

on the remote until the image appears.

 

 

 

 

 

 

 

 

 

 

 

If you are using a laptop the VGA output may have to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Be enabled to view an image.

 

 

 

 

 

 

 

 

 

 

 

Adjusting the image

 

 

 

 

 

 

 

 

 

 

 

Adjust the image by tilting the projector up or down

adjust height

Position the projector the desired distance from the screen at a 90-degree angle to the screen.

See page 8 for a table listing screen sizes and distances to the screen.

Remove the top front lid.

a.Slide the tabs on the side toward the rear of the projector to unlock the projector top cover.

b.Slide the top toward the front of the projector to unhook it from the projector body.

c.Lift off.

Image 11
Contents Kameleon HDP6000 Trademarks Safety Certifications. Regulatory Model H8300FCC Warning Declaration of ConformityTable of Contents Important Operating Considerations for Safety Introduction Product specificationsThree 12-volt DC outputs PowerRS232Rear Connector Panel Setting up the Projector Anamorphic Lens Projector PositioningVideo Quality Choosing the aspect ratioDigital connections Connecting a video deviceRemove the top front lid ? No start up screen? Get help onTurning off the projector Adjust the focus and zoomShutting down the projector Screen Save Time Auto Off TimeTroubleshooting your setup Activate the laptops external Page Page Still need assistance? Using the remote controlTroubleshooting the remote Optimizing computer images Presentation featuresUsing the keypad buttons Customizing the projector Using the menusOptimizing video images Basic Picture menu Advanced Picture menu Setup menu Status and Service menu Replacing the projection lamp MaintenanceHelp Wait 60 minutes to allow the projector to cool thoroughly Lamp replacement procedureUsing the Security Lock Communication configuration RS-232 terminal specificationsLimitations Error ConditionsFunction Command Response Page Page Page SplitScreen Compatibility Limited Warranty