Onkyo TX-SR573 First Time Setup—Continued, None, properly, press the remote controller’s TEST

Page 33

None.

First Time Setup—Continued

6 Use the Down [ ] button to select “Surround,” and then use

ENTER

the Left and Right [ ]/[ ] but- tons to select Small, Large, or

None.

Small: Select if the surround speak- ers are small.

Large: Select if the surround speak-

ENTER

ers are large.

None: Select if no surround speakers are connected.

Note:

•If the Front setting in step 4 is set to Small, the Large option cannot be selected.

Testing the Speakers

To make sure that all of the speakers are working

properly, press the remote controller’s [TEST

TONE] button. A test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again.

•If the test tone is not produced by a speaker, or it’s produced by a speaker other than the one shown on the display, you may have wired it incorrectly and should check your connections (see page 17).

•If the test tone is not produced by a speaker, and its name does not appear on the display, check the speaker conﬁguration (see page 32).

7

ENTER

ENTER

Use the Down [	] button to
select “Surr Back,” and use the
Left and Right [	]/[ ] buttons to

select Small, Large, or None.

Small: Select if the surround back speakers are small.

Large: Select if the surround back

speakers are large.

None: Select if no surround back speakers are connected.

Notes:

•If the Surround setting in step 6 is set to None, this setting does not appear.

•If the Surround setting in step 6 is set to Small, the Large option cannot be selected.

8 Use the Down [ ] button to select “Surr Back Ch,” and use

ENTER

the Left and Right [ ]/[ ] but- tons to select 2ch or 1ch.

2ch: Select if two (left and right) surround back speakers are connected.

1ch: Select if one surround back

ENTER

speaker is connected.

Note:

• If the Surround and Surr Back set- tings in steps 6 and 7 are set to None, this setting does not appear.

9Press the [SETUP] button.

Speaker conﬁguration is complete.

33

Image 33

Contents TX-SR573 ContentsInstruction Manual AV ReceiverAVIS Important Safety InstructionsMemory Backup Precautions4.Power For U.S. modelsFeatures Supplied AccessoriesRemote Controller ProcessingTurning On & First Time Setup ContentsUsing the Listening Modes IntroductionFront & Rear Panels Front Panel2 3 4 5 6 78 9J K L Display Front & Rear Panels—ContinuedFront & Rear Panels—Continued Rear PanelInstalling the Batteries Remote ControllerUsing the Remote Controller NotesRemote Controller—Continued About the Remote Controller ModesRECEIVER/TAPE Mode ASTANDBY button Remote Controller—ContinuedRemote Controller-Continued DVD ModeRemote Controller—Continued CD, MD & CDR ModesRemote Controller—Continued HDD ModeAbout Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting Your Speakers—ContinuedHow Many Speakers? Attaching the Speaker LabelsConnecting a Powered Subwoofer Connecting Speaker Set AConnecting Speaker Set B Connecting Your Speakers—ContinuedConnecting Antenna Connecting the AM Loop AntennaConnecting the Indoor FM Antenna Connecting an Outdoor FM Antenna Connecting Antenna—ContinuedConnecting an Outdoor AM Antenna NotesAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingWhich Connections Should I Use? Connecting Your Components—ContinuedVideo Connection Formats Audio Connection FormatsConnecting a TV or Projector Connecting Your Components—ContinuedHint Connecting Your Components—Continued Connecting a DVD playerConnecting Your Components—Continued Connecting a VCR or DVD Recorder for PlaybackVCR, DVD recorder or the otherConnecting Your Components—Continued Connecting a VCR or DVD Recorder for RecordingWith connection Connecting Your Components—ContinuedConnecting Your Components—Continued Connecting a CD Player or TurntableCD Player or Turntable with Built-inPhono Preamp StepConnecting Another Component’s Power Cord Connecting Your Components—ContinuedCassette recorder, CDR, etc Connecting the Power Cord Connecting -capableOnkyo ComponentsConnecting Your Components—Continued NotesTurning On & Standby Smooth Operation in a Few Easy StepsTurning On the AV Receiver Assigning Digital Inputs to Sources First Time SetupChanging the Input Display TUNER Digital inputs cannot be assigned toSpeaker Conﬁguration First Time Setup—ContinuedYes: Select if a subwoofer is con nectedproperly, press the remote controller’s TEST First Time Setup—ContinuedNone NotesPlaying Your AV Components Basic AV Receiver OperationPlaying Your AV Components—Continued Using the Multichannel DVD InputDisplaying Source Information Interpreting Surround Channel InformationListening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Displaying AM/FM Radio InformationListening to the Radio—Continued Connecting the XM AntennaListening to XM Satellite Radio Signing Up for XM Satellite Radioindicator Selecting XM Radio ChannelsListening to the Radio—Continued Channels cannot be selected while theDisplaying XM Radio Information Listening to the Radio—ContinuedSelecting XM Channels from the Front Panel XM Radio Messages Positioning the XM AntennaSETUP button Listening to the Radio—ContinuedSelecting Presets Presetting AM/FM Stations & XM ChannelsDeleting Presets the preset number ﬂashesAdjusting the Bass & Treble Setting the Display BrightnessCommon Functions Muting the AV ReceiverAdjusting Speaker Levels Using the Sleep TimerUsing Headphones Common Functions—ContinuedSelecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV receiverUsing the Listening Modes—Continued Using the Listening Modes—Continued About the Listening ModesUsing the Listening Modes—Continued Onkyo Original DSP ModesMono Movie OrchestraUsing the Late Night Function Dolby Digital only Using the CinemaFILTERUsing the Audio Adjust Settings Using the Listening Modes—ContinuedPL II & PL IIx Music Mode Settings Input Channel SettingsDTS Neo:6 Music Mode Setting Dolby Digital EX Input Signal SettingRecording the Input Source RecordingRecording from Different Sources 2.Prepare the VCR for recordingAdvanced Speaker Settings Advanced SetupCrossover Frequency Double BassSpeaker Distance Advanced Setup—ContinuedSpeaker Levels NotesAdvanced Setup—Continued Digital Signal Formatsbuttons to adjust the speaker 6Press the SETUP buttonEntering Remote Control Codes Controlling Other ComponentsNotes Resetting the Remote Controller Resetting the REMOTE MODE ButtonsControlling Other Components—Continued Controlling a TV Learning Commands from Other Remote Controllers Controlling Other Components—ContinuedNotes Making Macros Using MacrosRunning Macros Deleting MacrosTroubleshooting PowerAudio Troubleshooting—Continued VideoTuner Recording Remote ControllerOthers Troubleshooting—ContinuedAmpliﬁer Section SpeciﬁcationVideo Section Tuner SectionMemo ONKYO EUROPE ELECTRONICS GmbH ONKYO U.S.A. CORPORATIONONKYO EUROPE UK Office ONKYO CHINA LIMITEDPage Page Page Page Page Page Page Page Page Page Page Page Page