
Troubleshooting
| Problem |
| Check | Page | ||
|
|
| • | Projector power cord is not plugged into the wall outlet. | 20 | |
|
|
| ||||
|
|
| • | Power to the external connected devices is off. | — | |
|
|
| • | The selected input mode is wrong. | 29 | |
|
|
| • | Cables incorrectly connected to side panel of the projector. | ||
|
|
| • | Remote control batteries have run out. | 13 | |
No picture and no sound | ||||||
• | External output has not been set when connecting notebook computer. | — | ||||
or projector does not | • | The AV MUTE display appears. | 30 | |||
| start. | |||||
| • | The lamp unit and the lamp unit cover are not installed correctly. | 72 | |||
|
|
| ||||
|
|
| • | Cables incorrectly connected to the side panel of the projector. | ||
|
|
| ||||
|
|
| • | “Bright” is set to minimum position. | 40 | |
|
|
|
|
|
| |
Sound is heard but no |
|
|
| |||
picture appears |
|
|
| |||
|
|
|
|
|
| |
|
|
| • | Picture adjustments are incorrectly set. | 40 | |
|
|
| ||||
|
|
| (Video Input only) |
| ||
|
|
| • | Video input system is incorrectly set. | 55 | |
|
|
| (INPUT 1 only) |
| ||
|
|
| • | Input signal type RGB/Component is incorrectly set. | 40 | |
Color is faded or poor |
|
|
| |||
|
|
|
|
|
| |
|
|
| • | Adjust the focus. | 31 | |
|
|
| ||||
|
|
| • | The projection distance exceeds the focus range. | ||
|
|
| (Computer Input only) |
| ||
|
|
| • | Perform “Fine Sync” Adjustments (“Clock” Adjustment) | 42·44 | |
|
|
| • | Perform “Fine Sync” Adjustments (“Phase” Adjustment) | 42 | |
Picture is blurred; | • | Noise will appear depending on the computer. | — | |||
| noise appears |
|
|
| ||
|
|
| • | The “DNR” (Digital Noise Reduction) setting is not correct. | 54 | |
|
|
| • | Cables incorrectly connected to side panel of projector. | ||
|
|
| ||||
|
|
| • | Volume is set to minimum. | 29 | |
|
|
|
|
|
| |
Picture appears but no |
|
|
| |||
sound is heard |
|
|
| |||
|
|
|
|
|
| |
An unusual sound is | • | If the picture is normal, the sound is due to cabinet shrinkage | — | |||
occasionally heard |
| caused by a room temperature changes. This will not affect |
| |||
from the cabinet |
| operation or performance. |
| |||
| Maintenance | • | See “Maintenance Indicators”. | 70 | ||
indicator illuminates |
|
|
| |||
Image cannot be | • | The signal in INPUT 1 is not an analog RGB/Digital RGB SVGA | 56 | |||
| (800 ⋅ 600) signal. Images cannot be captured if the signals are |
| ||||
| captured |
|
| |||
|
| different from the above. |
| |||
|
|
|
|
| ||
|
|
| • | The signal in INPUT 1 is set to a resolution that exceeds SXGA. |
| |
Pict in Pict does not | • | The signal in INPUT 1 is sending Component signals 480I, | 51 | |||
| work |
| 480P, 720P, or 1080I. | |||
| • |
| ||||
|
|
| The signal in INPUT 1 is set to interlace mode using RGB signals. |
|
-76