Sharp PG-LX2000 appendix Rest your eyes occasionally, Avoid locations with extremes of temperature

Page 10

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center

for replacement.

See “Regarding the Lamp” on page 56.

Caution concerning the setup of the projector

■For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

Rest your eyes occasionally.

■Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.

When using the projector in high- altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

■When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

■Use the projector at altitudes of 2,300 meters (7,500 feet) or less.

Warning about placing the projector in a high position

■When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■Protect the lens so as not to hit or damage the surface of the lens.

Avoid locations with extremes of temperature.

■The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not set up the projector in places exposed to direct sunlight or bright light.

■Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector

■Place the projector on a level site within the adjustment range (9 degrees) of the adjustment foot.

■After the projector is purchased, a faint smell from the vent may appear when the power is fi rst turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.

Do not block the exhaust and intake vents.

■Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■Ensure that the intake vent and the exhaust vent are not obstructed.

■If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into Standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 54 and 55.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PG-LX2000 PG-LS2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Part Names and Functions 15 16Rear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Setup and Projection Easy StartTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorVideo Setup Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeSignal Input 169 Mode Screen Lens centerProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Press Enter to exit the Setup Guide screen About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjusting the Picture Size Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press KeystoneSwitching the Input Mode Adjusting the VolumePress Resize Resize ModeButton About Copyrights Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeFreezing a Moving Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Press Menu Using the Menu ScreenMenu Selections Quick Start Menu ExampleMenu Selections Complete Menu Example Adjusting BrightQuick Start Menu Following items can be configured on the Quick Start MenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Colors Adjusting the ImageAdjusting the Color Temperature Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Checking the Input Signal Setting the Video SystemSetting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Image Position Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Keystone CorrectionClosed Caption Setting the OverscanSetting the On-screen Display For Americas onlyReversing/Inverting Projected Images Selecting the Setup GuideSelecting the Background Image Selecting the Wall ColorSpeaker Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Fan Mode SettingSystem Lock Function To cancel the keycode that you have already setWhen the System Lock is set Enter the same keycode in Re- confirmTaking the Keylock Off Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function Select On, then press EnterReturning to the Default Settings Setting the Function Button OperationStandby Mode Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer Communication conditions RS-232C Specifications and CommandsComputer control Basic formatCommands ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check Sharp Electronics Corporation Specifications Dimensions Units inches mmIndex

PG-LS2000, PG-LX2000 specifications

The Sharp PG-LX2000 and PG-LS2000 are advanced multimedia projectors designed to cater to a variety of presentation needs in educational and professional environments. Both models boast impressive specifications that highlight their performance and usability.

The PG-LX2000 is a lightweight LCD projector, featuring a compact design that makes it easy to transport. It delivers a bright picture with a high brightness rating of 3,000 lumens, ensuring that images remain clear even in well-lit rooms. This model has a native XGA resolution of 1024 x 768 pixels, providing sharp images for detailed presentations. It supports a range of input options, including HDMI, VGA, and composite video, making it versatile for different devices.

On the other hand, the PG-LS2000 stands out with its laser technology. It utilizes a 3LCD laser light source that offers long-lasting brightness of 3,000 lumens, combined with a WUXGA resolution of 1920 x 1200 pixels. This projector provides wider color gamuts and enhanced contrast ratios, ensuring vibrant and dynamic visuals. The laser light source significantly reduces maintenance requirements, with a lifespan of up to 20,000 hours, yielding a lower total cost of ownership over time.

Both projectors feature a range of connectivity options, including USB Type-A and Type-B for easy integration with various computing devices. They support wireless presentation capabilities, allowing users to connect via mobile devices, streamlining setup for meetings and collaborative work. Additionally, the built-in 10W speaker enhances audio output, eliminating the need for external sound systems in smaller settings.

The PG-LX2000 and PG-LS2000 also incorporate features aimed at user convenience and digital signage. They include a quick start-up time, allowing presenters to begin within seconds. The projectors also offer a vertical keystone correction feature, compensating for image distortion when projecting at an angle, ensuring that the visual output is always aligned correctly.

Moreover, energy-saving technologies are integrated into both models, including eco modes that adjust brightness based on ambient light, contributing to reduced power consumption. They also support DICOM simulation mode, making them suitable for medical applications where precise imagery is crucial.

In conclusion, the Sharp PG-LX2000 and PG-LS2000 projectors encapsulate the brand’s commitment to quality, innovation, and user-friendly design. With their versatile features and robust performance, they are well-suited for educators, business professionals, and anyone in need of reliable presentation tools.
Top Page Image Contents