Sharp AR-162S operation manual Equipmentoptional

Page 57

● Since only one copy per original can be made, the number of copies cannot be changed.

● Press the CLEAR key to stop copying in the middle of a run.

While making copies from the SPF, do not place originals of the next copying job. Place them after all copies of the current job have been output.

55

5

Press the START key.

Stream feeding mode

If the stream feeding mode has been enabled using user program No. 4, the SPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed. While this indicator is blinking, any new originals placed in the SPF will be fed and copied automatically. See page 35, USER PROGRAMS.

1 Ensure that no original is left on the original table.

2 Adjust the original guides to the size of the originals.

Set the originals face up in the document feeder tray.

3 ● The SPF indicator will light up. If this indicator does not light up, the originals are not properly set or the SPF is not properly closed.

Ensure that the copy paper size in the paper tray is the

4 same size as the originals.

● For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides.

● Special originals such as transparency film and tracing paper should not be fed through the SPF but should be copied from the original table.

Using the SPF

● Be sure to remove any staples or paper clips from the originals.

● Damaged or crumpled originals may misfeed in the SPF. It is recommended that these originals be copied from the original table.

● Before placing curled or wavy originals into the document feeder tray, be sure to flatten them. If not, original misfeeds may result.

SINGLE PASS FEEDER (AR-SP2)

Single pass feeder (AR -SP2)

EQUIPMENTOPTIONAL

Image 57

Contents AR-162S Safety Precautions Contents Conventions used in this manual IntroductionMain Features Part Names and Functions Part Names and Functions Zoom indicator p.17 Interrupt key and indicator pPaper Size indicators Alarm indicatorsPreset Ratio selector keys and indicators Start key and indicatorOriginal Size Enter key and indicators Auto Image key and indicatorDo not install your copier in areas that are Copier InstallationDo not touch the photoconductive drum green portion Loading Copy Paper Gently lift and pull out the paper tray until it stopsPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Turn the power switch on Adjust the copy densityNormal Copying Set the number of copies using the numeric keys How to remove the platen coverNormal Copying Press the Start keyAutomatic REDUCTION/ENLARGEMENT/ZOOMPress the Auto Image key Set the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualSet the number of copies and press the Start key Unfold the bypass tray Bypass Feed special paperBypass Feed special paper TWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display key XY Zoom Use the Preset Ratio selector , keys and zoomPress the B/W Reverse key Check the copy paper size ReversePress the Dual page Copy key Dual page CopyInterrupting a Copy RUN Press the Interrupt keyStart key to resume copying Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModeRemove the new toner cartridge from the bag. Grasp Push the toner cartridge lock release lever and pullToner Cartridge Replacement Toner cartridge lifePress the light key Misfeed in the bypass tray Misfeed RemovalMisfeed in the copier First confirm the misfeed locationCarefully remove the misfed paper. Turn the roller Misfeed RemovalRotating knob in the direction of the arrow to assist Removing itMisfeed in the transport area Close the side cover by pressing the handle on Cover Misfeed in the paper trayDeveloper Required Maintenance RequiredUser Programs List of user programsProgram No Program name Description Enter a program number using the numeric keys Setting the user programsUser Programs Program name Program NoProgram name Parameters Select the desired parameter using the numeric keysSettings for auditing accounts Select the desired setting using the numeric keysEnter a 3-digit account number using the numeric keys Program No Account number change Press and hold down the 0 key Use the copy ratio display key to select the account NumberProgram No Resetting account Power Save Modes Preheat modeAuto power shut-off mode Power Save Modes Setting the power save modesCopying from the preheat mode User Maintenance Original table and platen coverBypass tray paper feed roller Transfer charger cleaning User MaintenanceCopier TROUBLE? Problem SolutionCopier TROUBLE? Example Self-diagnostic functionTypes and sizes of copy paper SuppliesGenuine supplies statement SuppliesProper storage Store the supplies in a location that isSpecifications Specifications Optional Equipment Specifications Single Pass Feeder AR-SP2Part Names Equipmentoptional Misfeed removal Single Pass Feeder AR-SP2Index Index Material Safety Data Sheet Special Fire Fighting Procedure Ignition TemperatureFlash Point Method Used Flammable LimitsOther Limits Ingredients CAS No ProportionRoutes of Entry Skin? Ingestion?None required under normal use Memo Memo Page Sharp Corporation

Related manuals

Manual 68 pages 5.92 Kb