Sharp MX-M564N, MX-M364N, MX-M464N manual Installation notes, About consumables

Page 4

Installation notes

CAUTION

Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can withstand the weight of the machine.

Risk of injury due to the machine falling or toppling.

If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface that can withstand the weight of the product.

Do not install in a location with moisture or dust.

Risk of fire and electrical shock.

If dust enters the machine, dirty output and machine failure may result.

Locations that are excessively hot, cold, humid, or dry (near heaters, humidifiers, air conditioners, etc.)

The paper will become damp and condensation may form inside the machine, causing misfeeds and dirty output. SPECIFICATIONS (page 10)

If the location has an ultrasonic humidifier, use pure water for humidifiers in the humidifier. If tap water is used, minerals and other impurities will be emitted, causing impurities to collect on the inside of the machine and create dirty output.

When the machine is installed, the adjusters (4) must be lowered to the floor to secure the machine (prevent it from moving).

Rotate the adjusters in the locking direction until they are in firm contact with the floor.

If you find it necessary to reposition the machine due to rearrangement of

Lock

Release

 

 

your office layout or other reason, retract the adjusters from the floor, turn

 

 

off the power, and then move the machine.

 

 

(After moving the machine, lower the adjusters again to secure the machine.)

Locations exposed to direct sunlight

Plastic parts may become deformed and dirty output may result.

Locations with ammonia gas

Installing the machine next to a diazo copy machine may cause dirty output.

Do not install the machine in a location with poor air circulation.

A small amount of ozone is created inside the machine during printing. The amount of ozone created is not sufficient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation. (The odor may occasionally cause headaches.)

*Install the machine so that people are not directly exposed to exhaust from the machine. If installed near a window, ensure that the machine is not exposed to direct sunlight.

Near a wall

 

30 cm

 

 

Be sure to allow the required space around the machine for

 

 

servicing and proper ventilation. (The machine should be no closer

 

 

than the distances indicated below from walls. The indicated

 

 

distances are for the case when a saddle finisher and large capacity

30 cm

45 cm

paper tray are not installed.)

Locations subject to vibration.

Vibration may cause failure.

CAUTION

The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular, never move the machine while the power is on.

The machine should be installed near an accessible power outlet for easy connection.

Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

About consumables

CAUTION

Do not throw a toner cartridge into a fire.

Toner may fly and cause burns.

Store a toner cartridge out of the reach of children.

4

Image 4
Contents Quick Start Guide Warranty EMC this machine and peripheral devicesFor the users of the fax function FAX interface cable and Line cableSymbols in this manual Power notesInstallation notes About consumablesHandling precautions Laser informationNoise emission Storage of suppliesSupply of spare parts and consumables Noise emission valuesPart Names Operation panelTurning the Power on and OFF Turning on the powerTurning off the power Restarting the machineHow to read the Operation Guide Before using the machinePrinting and faxing from a computer Directions for useBasic Specifications / Copier specifications SpecificationsAutomatic document feeder Finisher Tray 2 / 3 / 4Saddle stitch finisher large stacker Saddle stitch finisher Finisher large stackerPunch module for saddle finisher Punch module for finisherNetwork Printer Specifications Fax SpecificationsNetwork Scanner Specifications System settings password To the Administrator of the MachineFor the users of the fax function Information on Disposal Information on Disposal for Users private householdsInformation on Disposal for Business Users European UnionMX-M364N/MX-M464N/MX-M564N Quick Start Guide