Sharp PN-E602 operation manual Controlling with a PC, Basic operation

Page 44

Controlling the Monitor with a PC (LAN)

6. Click on “LAN SETUP” under NETWORK.

7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.

Controlling with a PC

■ Basic operation

You use Internet Explorer on a PC on the LAN to control the monitor.

1.Launch Internet Explorer on the PC.

2.In the “Address” box, type “http://” followed by your monitor’s

IP address followed by “/”, then press the Enter key.

You can confirm the IP address with the DISPLAY function.

When prompted to enter a user name and password, type the user name and password that you specified in the security settings (see page 46), and click [OK].

If you did not make any security settings, leave the spaces blank and click on [OK].

3.You can check, control, and change the monitor’s status and settings by clicking the menu items on the left side of the screen.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”.

To set the address manually, set this to “OFF”.

IP ADDRESS

If the DHCP CLIENT is set to “OFF”, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to “OFF”, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to “OFF”, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

8.When the setting is changed, click [Apply].

9.Check the message and click [OK].

10.Exit Internet Explorer.

11.Restore the PC’s IP address jotted in Step 6, “(2) Specifying the PC’s IP address”.

12.Connect the monitor and the PC to the LAN.

Caution

•Wait 10 seconds after clicking [OK] before proceeding.

•When operating using the remote control unit or similar, click [Refresh].

TIPS

•When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 23.)

•If you see an [Apply] button next to a setting, click it after you change that setting.

TIPS

•See pages 45 to 49 for details on each setting.

•If you click [Refresh] before the screen finishes updating the current display, the “Server Busy Error” will appear. Wait for a moment before operating your monitor again.

•You cannot operate the monitor while it is warming up.

•If “DHCP CLIENT” is set to “ON”, press DISPLAY on the remote control unit two times and then check the monitor’s IP address.

E44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents PN-E602 For Customers in U.K GREEN-AND-YELLOWBlue BrownRefer Servicing to Qualified Service Personnel Important InformationInformation on Disposal for Users private households Information on Disposal for Business UsersEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Tips and Safety Instructions Do not place the monitor on a device which generates heat For the monitor in landscape orientationFor the monitor in portrait orientation Contents Supplied ComponentsNRear view Part NamesNFront view NRemote control unit Part Names Signal transmitterPower button See Mute button See 11 EConnecting Peripheral Equipment Connection with a PC or AV equipmentConnecting Peripheral Equipment 13 ERemoving the Handles Connecting the Power CordBinding Cables Preparing the Remote Control Unit Installing the batteriesRemote control operation range 15 ETurning Power On/Off Turning on the main powerTurning power on/off Main power switchDisabling power on/off operations NDate/time settingTurning Power On/Off 17 EBasic Operation MuteMenu DisplayBasic Operation NSwitching the screen size 19 EWide Zoom Normal Dot by DotMenu Items Displaying the menu screenNExample of operation NMenu screen display21 E Menu item detailsNSCREEN Menu Items NPICTURENAUDIO NSETUPMenu Items 23 E NOPTIONNMULTI Menu Items NDual screen display 25 ENPIP/PbyP NZOOM2 Special Setting Setting procedureSet using the Multi menu Menu Items NEnlargePower 27 ENSCHEDULE DAY of the WeekNScreen display for adjustment Adjustments for PC screen displayNAutomatic adjustment 29 E Communication procedure Controlling the Monitor with a PC RS-232CPC connection Communication conditionsNID numbers 31 ENResponse code format 002 VOLM0030VOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data 33 ERS-232C command table Power control/Input mode selectionHow to read the command table Command Command field See Direction35 E Controlling the Monitor with a PC RS-232C Screen menuControlling the Monitor with a PC RS-232C Picture menu Controlling the Monitor with a PC RS-232C Audio menu Setup menu37 E Controlling the Monitor with a PC RS-232C Option menu Image Position Epos setting 39 EControlling the Monitor with a PC RS-232C Multi menu Landscape orientation Portrait orientationInitialization/Functional Restriction Setting Function menu Controlling the Monitor with a PC RS-232C PIP/PbyP menuControlling the Monitor with a PC RS-232C Others Commands for setting of the Gamma user data41 E To set on the monitor Settings to connect to a LANControlling the Monitor with a PC LAN Default Gateway 0.0 43 ETo set from a PC Controlling the Monitor with a PC LANSee pages 45 to 49 for details on each setting Controlling with a PCBasic operation If the Dhcp Client is set to OFF, specify an IP addressInformation about this monitor appears Standby mode, Power on is the operation available45 E User Name / Password If the Dhcp Client is set to OFF, specify the subnet maskDNS Server Accept IP Address47 E Attach the log file to a TEMPERATURE/HARDWARE error e-mail Recipient E-MAIL AddressesCondition Confirmation49 E Troubleshooting Troubleshooting 51 ESpecifications NProduct SpecificationsNDimensional Drawings SpecificationsNPower management 53 ESpecifications NCompatible signal timing PC NCompatible signal timing AV55 E Mounting Precautions For Sharp dealers and service engineers PN-E602 Mu EN11L1
Related manuals
Manual 2 pages 13.57 Kb
Top Page Image Contents