Sharp XG-C430X, XG-C335X, XG-C330X Controlling the Projector via LAN, Version 5.0 or later

Page 24

Controlling the Projector via LAN

After connecting the projector to your network, enter the projector IP address in “Address” on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network.

Controlling the Projector

Using Internet Explorer

(Version 5.0 or later)

Complete connections to external equipment before starting the operation. (See pages 21- 29 of the projector’s operation manual.)

Complete the AC cord connection. (See page 30 of the projector’s operation manual.)

Note

•When connecting the projector to the LAN, use a LAN cable (Category 5). When connecting the projector to a hub, use a straight-through cable.

1 Start Internet Explorer (version 5.0 or later) on the computer.

2 Enter “http://” followed by the projector IP address set by the procedure on page 23 followed by “/” in “Address”, and then press the “Enter” key.

•The factory default setting for the projector : “DHCP Client” is “Off” and IP address is “192.168.150.2”. If you did not change the IP address in “3. Setting up a Network Connection for the Projector” (pages 22-23), enter “http:// 192.168.150.2/”.

3

A screen for controlling the pro- jector appears, ready for per- forming various status condi- tions, control, and settings.

-24

Image 24

Contents Setup Manual Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceScreen 12.2 15.2m 50ftNormal Mode Stretch ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mmWide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mmTele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mmTele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mmTele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mmChanging the Lens InfoReplace the lens housing cover Insert the lens into the projectorConnecting Pin Assignments COMPUTER-RGB Input/Output Component Input/OutputConnecting Pin Assignments Pin No. SignalRS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W RReturn DVI Progressive 3D OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Setting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Launch general purpose terminal emulatorWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu View Setting Detail List VView All SettingSet Items Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDhcp Client Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminalTroubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mmWhen AN-C12MZ is installed When AN-C18MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed

Related manuals

Manual 2 pages 32.09 Kb