Sharp XG-F210X, XG-F260X operation manual Upper side, On the remote, Control

Page 21

4.Adjust the projected image with the Setup Guide

1After the projector turns on, the Setup Guide appears. (When ÒSetup GuideÓ is set to ÒOnÓ. See page 42.)

2Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).

3After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide.

_PP. 26, 27

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the projector

Shrinks	Shrinks
upper side.	lower side.

On the remote control

_P. 28

6. Select the INPUT mode

Select the ÒCOMPUTERÓ using INPUT on the projector or COMPUTER on the remote control.

Quick Start

On the On the remote projector control

INPUT listOn-screen display (RGB)

INPUT
INPUT		COMPUTER
COMPUTER		RGB
COMPUTER		1024 ⋅ 768
		1024 ⋅ 768

DDVI-D Computer

DDVI-D Video

•When you press INPUT on the projector, the INPUT list appears. Press '/" to switch the INPUT mode.

_P. 29

7.Turn the computer on

8.Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.

On the	On the remote	On-screen display
On the	On the remote
projector	control

_P. 25

17

Image 21

Contents XG-F260X XG-F210X Model No Serial No Iii Page IntroductionENGLISH Information For Future Reference Using the Menu ScreenContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents See Replacing the Lamp onTemperature monitor function Using the projector in other countriesIf the projector starts to overheat due to setup Other connected equipmentOptional accessories AccessoriesProjector Part Names and FunctionsAudio 1 input terminal Rear ViewButtons For switching to Respective input Modes Standby button For putting Projector into Standby modeAdjustment Setting screens,Inserting the Batteries Remote control can be used to control Usable RangeProjector within the ranges shown Illustration When connecting equipment other than a computer, see Setup and ProjectionOn the projector On the remote control Quick StartUpper side On the remoteControl Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Connecting the Power Cord AC socket To AC outlet Power cord suppliedControlling the Projector by a Computer Turning the Projector On/Off Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector on On-screen display confirmation messageAdjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Picture Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightPress P/Q or O/R to adjust Keystone Correction Press Keystone to enter the Keystone Correction modeAdjustment buttons P/R/O/Q Return button Keystone button On-screen display Keystone Correction modeAdjusting the Volume Switching the Input ModeButtons AV Mute button VOL +/- Volume buttons On-screen displayPress Resize Resize ModeVideo Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreeze button Picture Mode button Auto Sync button Freezing a Moving ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingMenu Items Computer RGB, DVI RGB inputComputer Component DVI Component, S-VIDEO, Video input ÒHelpÓ menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Example Adjusting BrightPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterExample Picture screen menu for Computer RGB input Picture Adjustment Picture MenuMenu operation n Adjusting the ImageAdjusting the Projected Image SCR ADJ Menu You can move the projected image verticallySee page 28 for details of Keystone Correction Button Adjusting the Projected Image SCR ADJ Menu Adjusting the Projector Function PRJ ADJ Menu This function changes the fan rotation speed Adjusting the Projector Function PRJ ADJ MenuEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off Troubleshooting with the Help Menu Utilizing the Help Menu FunctionsPress Oor Qto select Help, then Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseGND Connecting Pin AssignmentsProjector Computer Return code 0DH RS-232C Specifications and Command SettingsCommands RGB PAL Control Contents Return DVI-D Computer Compatibility Chart21-24 Troubleshooting47-49 For Sharp Assistance Specifications Dimensions Index