Sharp XG-F260X, XG-F210X operation manual Regarding the Lamp, Replacing the Lamp

Page 54

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 44.)

Purchase a replacement lamp of type AN-XR30LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal

Information

 

www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

50

Image 54
Contents XG-F260X XG-F210X Model No Serial No Iii Page IntroductionENGLISH Information Using the Menu Screen For Future ReferenceContents Reference Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally See Replacing the Lamp onIf the projector starts to overheat due to setup Using the projector in other countriesTemperature monitor function Other connected equipmentAccessories Optional accessoriesPart Names and Functions ProjectorRear View Audio 1 input terminalAdjustment Standby button For putting Projector into Standby modeButtons For switching to Respective input Modes Setting screens,Inserting the Batteries Remote control can be used to control Usable RangeProjector within the ranges shown Illustration On the projector On the remote control Setup and ProjectionWhen connecting equipment other than a computer, see Quick StartUpper side On the remoteControl Standard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Connecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Audio OUT Connecting the Power Cord AC socket To AC outlet Power cord suppliedControlling the Projector by a Computer Turning the Projector on Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector On/Off On-screen display confirmation messageAdjusting the Picture Size About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjustment buttons P/R/O/Q Return button Keystone button Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction On-screen display Keystone Correction modeButtons AV Mute button VOL +/- Volume buttons Switching the Input ModeAdjusting the Volume On-screen displayResize Mode Press ResizeVideo Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeFreeze button Picture Mode button Auto Sync button Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen left-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When right-clickingMenu Items Computer RGB, DVI RGB inputComputer Component DVI Component, S-VIDEO, Video input Items you can set with the Help menu ÒHelpÓ menu nPress Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Example Adjusting BrightPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterPicture Adjustment Picture Menu Example Picture screen menu for Computer RGB inputAdjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ Menu You can move the projected image verticallySee page 28 for details of Keystone Correction Button Adjusting the Projected Image SCR ADJ Menu Adjusting the Projector Function PRJ ADJ Menu Adjusting the Projector Function PRJ ADJ Menu This function changes the fan rotation speedEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off Troubleshooting with the Help Menu Utilizing the Help Menu FunctionsPress Oor Qto select Help, then Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer How to Use the Storage Case Storing the ProjectorConnecting Pin Assignments GNDProjector Computer RS-232C Specifications and Command Settings Return code 0DHCommands RGB PAL Control Contents Return Computer Compatibility Chart DVI-DTroubleshooting 21-2447-49 For Sharp Assistance Specifications Dimensions Index