Sharp XR-50S, XR-55X Inserting the Batteries, Usable Range, Remote control signal transmitters

Page 19

Inserting the Batteries

1 Pull down the tab on the cover and remove the cover towards the direction of the arrow.

2 Insert the batteries.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

3 Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below

Caution

Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.

Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

Batteries of different types have different properties, therefore do not mix batteries of different types.

Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then remove them using a cloth.

The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.

Remove the batteries from the remote control if you will not be using the remote control for a long time.

Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

The signal from the remote control can be refl ected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control

Ensure that you do not drop it or expose it to moisture or high temperature.

The remote control may malfunction under a fl uorescent lamp. In this case, move the projector away from the fl uorescent lamp.

Remote control sensor

30°

30°

33 n (10 m)

Remote control signal transmitters

Remote control

15

Image 19
Contents XR-55X XR-50S Model No Serial No Iii Page Void the users authority to operate this equipment IntroductionENGLISHSharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARP InformationFor Future Reference Using the Menu ScreenContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals For displaying the break time Break Timer buttonPicture Mode button CLICK/EFFECT button 34Inserting the Batteries Remote control signal transmittersUsable Range Easy Start Setup and ProjectionOn the remote Control Turn the computer on Turn the power offSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Monitor OUT AC socket Power cord To AC outlet supplied Connecting the Power CordControlling the Projector by a Computer Turning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenMake small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Adjustment buttons P/R/O/Q Return button Keystone buttonOn-screen display Keystone Correction mode Correcting Trapezoidal DistortionAdjusting the Volume Switching the Input ModeInput buttons AV Mute button VOL +/- Volume buttons Buttons Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingPicture menu Menu ItemsCOMPUTER/COMPONENT Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be configured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuImage while watching it To adjust the projectedSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsEco+Quiet Selecting the Film ModeReducing Image Noise DNR Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesAuto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingFan Mode Setting Adjusting the Projector Function PRJ-ADJ1/2 MenuSystem Lock Function Select On, then press Enter Setting the Function Button OperationKeylock Function Selecting the Quick Start MenuChecking the Lamp Life Status Standby ModeCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsRed on Abnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Basic format RS-232C Specifications and CommandsComputer control Communication conditionsCompuer Projector CommandsRGB PAL CC1 Computer Computer Compatibility Chart21-24 Troubleshooting53, 54 For Sharp Assistance Specifications Dimensions Index Kensington Security Standard connector ·················13Appendix
Related manuals
Manual 77 pages 60.28 Kb