Sharp XG-PH70X-N operation manual Temperature is

Page 97

 

Maintenance indicator

Problem

Cause

Possible solution

 

 

 

 

 

 

Normal

Abnormal

 

 

 

 

 

 

 

 

 

 

 

 

 

• Relocate the projector to an area

 

 

 

 

 

• Blocked air intake

with proper ventilation. (See page

 

Temperature

 

 

The internal

 

9.)

 

 

 

 

Red on

• Cooling fan break-

• Take the projector to your nearest

 

warning

Off

temperature is

 

(Standby)

down

Sharp Authorized Projector Dealer

 

indicator

 

abnormally high.

 

 

• Internal circuit failure

or Service Center for repair. (See

 

 

 

 

 

 

 

 

 

 

• Clogged air intake

page 104.)

 

 

 

 

 

• Clogged intake vent

• Clean the air vents and the intake

 

 

 

 

 

cover

vent cover. (See page 93.)

 

 

 

 

 

 

 

 

 

 

 

 

 

The lamp does

• The lamp is shut

• Disconnect the power cord from

 

 

 

 

the AC outlet, and then connect it

 

 

 

 

not illuminate.

down abnormally.

 

 

 

 

again.

 

 

 

 

 

 

 

 

 

Red on

 

 

 

 

 

Lamp

Green on

Time to change

• Remaining lamp life

• Carefully replace the lamp. (See

 

Green blinks

 

page 97.)

 

indicators

when the lamp

 

the lamp.

becomes 5% or less.

• Take the projector to your nearest

1, 2

is warming up.

 

 

 

Sharp Authorized Projector Dealer

 

 

 

Red on

The lamp does

• Burnt-out lamp

or Service Center for repair. (See

 

 

 

page 104.)

 

 

 

(Standby)

not illuminate.

• Lamp circuit failure

• Please exercise care when

 

 

 

 

 

 

replacing the lamp.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Securely install the cover.

 

 

 

 

The power

 

• If the power indicator blinks even

 

 

 

 

 

when the intake vent cover is

 

Power

Green on/

Red

indicator blinks in

• The intake vent

 

securely installed, contact your

 

indicator

Red on

blinks

red when the

cover is open.

 

nearest Sharp Authorized Projector

 

 

 

 

projector is on.

 

 

 

 

 

 

Dealer or Service Center for

 

 

 

 

 

 

 

 

 

 

 

 

advice. (See page 104.)

 

 

 

 

 

 

 

 

 

Info

•If the temperature warning indicator blinks and the projector enters the standby mode, the temperature warning indicator starts to illuminate. Check whether any of the ventilation holes are blocked (see page 10) and then try turning the power back on. Wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

•If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

•The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

Appendix

-95

Page 96 Page 98
Image 97
Page 96 Page 98
Contents XG-PH70X Special Note for Users in the U.K Model No Serial NoIntroduction Product Disposal Operation Buttons used in thisPreparing ContentsUsing Reference For Windows¨ When you want to view the setup manualFor Macintosh¨ Accessories CleaningPower Sources Power-Cord ProtectionAvoid locations with extremes of tem- perature Rest your eyes occasionallyTemperature monitor function Using the projector in other countriesOptional lens installation Do not block the intake and exhaust ventsSupplied accessories AccessoriesOptional accessories CableOptional lenses Throw DistanceLens ScreenProjector Part Names and FunctionsPower indicator About the Indicators on the ProjectorLamp indicators 1 Temperature warning indicatorInput 1 terminal Projector Side ViewClick/UNDO button Mouse/adjustment button 19á56 //\ Remote ControlWhen using the remote control Using the Remote ControlUsable Range Inserting the BatteriesSwitching the Remote Control Mode Using the Remote Control with a Signal CableUsing the Remote Control as a Wireless Computer Mouse Quick Start Setup and ProjectionAdjust the angle Setting Up the Projector Setting Up the ProjectorSet to Front Projecting a Reversed ImageINPUT/OUTPUT Terminals and Connectable Main Equipment ConnectionsSamples of Cables for Connection You may need other cables or connectors not listed belowSamples of Cables for Connection Connecting with the RGB Cable Connecting to a ComputerSide view Connecting with a 5 BNC to 15-pin D-sub CableConnections Connecting with a DVI Digital CableConnecting to Video Equipment Select the input signal type of the video equipment. See Connecting to RGB Video Equipment with a 5 RCA RGB Cable Connections Connecting with an S-video Cable or a Composite Video Cable Controlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableConnecting to a Monitor That Has an RGB Input Terminal Connecting to an Amplifier or Other Audio EquipmentTurning the Power Off Put Connecting the Power CordTurning the Projector On/Off Turning the Projector OnShifting the Lens Image ProjectionPress on the projector or on the remote control Using the Adjustment FeetWhile lifting the projector, rotate the adjustment feet Lens Shift buttonAdjusting the Projected Image Size Adjusting the FocusZoom button Focus button Focus buttons Zoom buttons Select the type of the keystone correction Correcting Trapezoidal DistortionPress or to set the posi- tion Geometric AdjustmentMatch screen’s four sides to green test pattern Keystone Press , , \ or to correct Adjustment withImage distortion Press or to set the po- sitionInput buttons Switching the Input ModePress on the remote control Adjusting the VolumeTurning Off the Sound Temporarily Displaying an Enlarged Portion of an ImagePress on the remote control to cancel the operation Selecting the Picture ModeUndo button Picture Mode button Freezing a Moving ImageMouse/adjustment button //\ Undo button Resize ModeVideo Button Adjustment Displaying and Setting the Break TimerDisplaying the Black Screen Black Screen buttonFollowing shows the items that can be set in the projector Menu ItemsMenu Items S. menu Input 1 / Input 2 / Input 3 Main Menu Options 1 menuOptions 2 menu Language menu Status menu Menu Selections Adjustments Using the Menu ScreenExample Adjusting Bright Example Picture screen menu for Input 1 RGB modePress or to select the item you want to adjust To adjust the pro- jected image while viewing itPress \ or to adjust the item selected Single adjustment itemExample Setting OSD Display Menu Selections SettingsSub menu Press or to select the item you want to setMenu screen will disappear Adjusting the Image Picture Adjustment Picture menuSelect a picture mode before adjusting the im- age Emphasizing the Contrast Adjusting the Color TemperatureReducing Image Noise DNR Selecting the Progressive ModeMake sure to set DNR to OFF in the following cases Input 1/INPUT Signal Type SettingExample C.M.S. screen menu Description of C.M.S. Adjustment Selecting the Color Repro- duction ModeColor Management System C. M. S. menu Selecting the Target ColorSetting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorExample C.M.S. screen menu Description of Brightness Example C.M.S. screen menu Description of Chromatic ValueResetting User-defined Color Settings Setting the Hue of the Target ColorExample C.M.S. screen menu Description of Reset Example C.M.S. screen menu Description of HueExample C.M.S. screen menu Overview of All Color Set- tingsAdjusting the Computer Image Computer Image Adjustment Fine Sync menuSaving Adjustment Settings Example Fine Sync screen menu for Input 1 RGB modeSpecial Mode Setting Selecting Adjustment Set- tingsAuto Sync Adjustment Checking the Input SignalDescription of Auto Sync Adjustment Used to automatically adjust a computer imageUsed to set the display during Auto Sync Auto Sync Display FunctionAdjusting the Audio Audio Adjustment Audio menuSetting the Audio Output Type Example Audio screen menu Description of Adjustment ItemsExample Audio screen menu Description of Speaker Settings Speaker SettingSetting the Resize Mode Using the Options 1 MenuExample Options 1 screen menu for Input 1 RGB mode Selectable Items of Resize ModeDescription of OSD Display Settings Setting On-screen DisplayShifting the Projected Im- age Vertically Digital Shift Capturing Projected Images Setting the Video SystemSelecting the Startup Image Selecting the Background ImageDetecting the Input Sig- nals Automatically Eco ModeSelect System Lock on the Op Auto Power Off FunctionTions 1 menu, then press Press the 4 buttons on the remoteEnter the same keycode in Recon- firm When the System Lock is setWhen the system lock is set If You Forget Your Password Setting a PasswordExample Options 2 screen menu Example Options 2 screen menu Description of Lamp Mode Setting the Lamp ModeChecking the Lamp Life Status Reversing/Inverting Pro- jected Images Description of Stack SettingExample Options 2 screen menu Description of PRJ Modes Locking the Operation But- tons on the Projector Shortcut to Make Projector Stack SettingsSelect Pair Stack on the Option Menu, and then press Select OK, and then pressExample Options 2 screen menu Description of Fan Mode Selecting the Fan ModeBypassing Unused Input Selections Example Options 2 screen menu Description of Set InputsSelecting the Transmis- sion Speed RS-232C Direct Power On FunctionExample Options 2 screen menu Description of RS-232C LAN/RS232C Setting Monitor Output SettingsExample Options 2 screen menu Description of Monitor Out Description of LAN/RS232CTCP/IP Setting Dhcp Client SettingExample Options 2 screen menu Description of Dhcp Client Set the TCP/IP manuallyEnter Gateway using , , and \, then press Service ModeOnly the service centers use the menu. Do not use the menu Description of TCP/IPReturning to the Default Settings Overview of All Menu Set- tings Selecting the On-screen Display LanguageExample Language screen menu Example Status screen menuCleaning the projector MaintenanceCleaning the air vents and the intake vent cover Cleaning the lensAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Temperature is Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Insert the new lamp unit Remove the lamp unitReplace the lamp unit cover Connect the power cord Resetting the Lamp TimerReset the lamp timer Reset the lamp timer after replacing the lampComputer Computer Compatibility Chart100 101 DTV102 Troubleshooting103 Problem Check104 For Sharp Assistance105 Specifications106 Glossary107 IndexSharp Corporation

XG-PH70X-N, XG-PH70X specifications

The Sharp XG-PH70X and XG-PH70X-N are high-performance projectors designed for professionals who require high-quality images and versatile connectivity options. These models offer a perfect blend of advanced technology and user-friendly features, making them ideal for a variety of applications, from corporate presentations to educational settings.

One of the standout features of the XG-PH70X series is its impressive brightness level, peaking at 7,000 lumens. This high lumen output ensures clear and vivid images even in well-lit environments, which is crucial for maintaining visibility during presentations or lectures. The XG-PH70X utilizes Sharp’s proprietary DLP technology, which is renowned for delivering sharp, vibrant colors and high contrast ratios. This technology is particularly effective in producing images that are both detailed and lifelike.

In terms of resolution, the XG-PH70X supports native WUXGA (1920 x 1200), allowing it to display full HD content with impressive clarity. The projector also features a dynamic contrast ratio that enhances the depth and richness of the projected images, ensuring that both dark and bright scenes are rendered accurately.

Connectivity options are another strong point of the XG-PH70X series. The projectors are equipped with multiple input ports, including HDMI, DisplayPort, and VGA, allowing for seamless integration with various devices such as laptops, Blu-ray players, and media servers. This versatility makes it easy to connect and display content from multiple sources.

Moreover, the XG-PH70X and XG-PH70X-N models come with advanced networking capabilities, including support for wired and wireless LAN connections. This feature allows users to share content from their devices effortlessly, contributing to a more collaborative and engaging presentation experience.

The projectors also offer an extended lamp life, which reduces maintenance costs and downtime. With options for eco-friendly modes, users can optimize the projector’s performance based on their specific needs, further enhancing its usability.

Portability is also a key feature, as these projectors are designed to be lightweight and easy to transport. This makes them suitable for traveling professionals who may need to set up presentations in various locations.

In summary, the Sharp XG-PH70X and XG-PH70X-N projectors are engineered to deliver exceptional performance, versatility, and ease of use. With their high brightness, advanced connectivity options, and user-friendly features, they are well-suited for demanding professional environments.
Top Page Image Contents