Visioneer 8820 manual Adjusting the Settings on the Scan Manager PRO

Page 57

ADJUSTING THE SETTINGS ON THE SCAN MANAGER PRO 53

3.Put the pointer on the image and drag the mouse to enclose the section you want in the scanned image.

As you drag the mouse, a dotted box appears on the image and the size settings change to reﬂect the new output size area. You can also type in the size settings boxes.

■Width and Height—the measurements of the ﬁnal image after it’s scanned; for example, if you plan to print the image on a typical piece of paper, the width and height are 8.5 and 11.0 inches

■Units—units of measurement for the new area; click the drop- down arrow and choose new units if you want

■Resolution—the dots-per-inch (dpi) setting for the new area

■Scale—the amount of enlargement or reduction of the image to ﬁll the width and height measurements; for example, if you select a small area and have set the width and height to a paper size, the scale automatically increases to enlarge the small image so it’s the same size as the paper

A new Scan Info box on the lower left portion of the Scan Manager Pro shows the information for the new area.

You can select multiple areas. A new Scan Info box appears for each one.

The following ﬁgure shows an example of a manually selected area.

Note: When you manually select an area, the settings on the other panels are for that selected area, not the whole image. For example, the histogram on the resolution panel and the response curve on the brightness and contrast panel refer to only your newly selected area.

Image 57

Contents Visioneer OneTouch Scanner P Y R I G H T I N F O R M a T I O N B L E O F C O N T E N T S Visioneer OneTouch 8820 Scanner Specifications WHAT’S in the BOX WelcomeVisioneer Onetouch 8820 Scanner Visioneer ONE Touch 8820 Scanner Getting the Paperport Software USER’S Guide What YOU NeedTo install the PaperPort software InstallingVisioneer Onetouch 8820 Scanner Installation Guide To connect the OneTouch 8820 scanner to a USB port Connecting the ScannerVisioneer Onetouch 8820 Scanner Installation Guide Power cord To check the status of the scanner Checking OUT Your ScannerIf the Scanner is not Properly Connected To connect the scanner Scan with the Scanner Buttons Three Ways to Scan Paper ItemsScan from the Screen Scan from the PaperPort Software or Other Twain SoftwareTo scan by pressing a button on the scanner Scanning Paper Items with the Onetouch ButtonsTo scan from the screen Scanning from the Button Panel on the ScreenAbout the Onetouch Buttons Button Preconﬁgured SettingsScanning Transparencies Brief ExplanationTo position a transparency for scanning Mask for 5 by Mask for 35mm film Scanning Transparencies To scan the transparency Scanning Transparencies Configuring the Scanner To display the Conﬁguration dialog box from the Button Panel About the Configuration Dialog BOXClick this Getting Help To select new options for a scanner button Selecting NEW Options for the ButtonsCreating NEW Configurations Adjusting Scan Settings and page SettingsTo adjust the scan settings and page settings Visioneer Onetouch 8820 Scanner Installation Guide Configuring the Scanner Visioneer Onetouch 8820 Scanner Installation Guide Configuring the Scanner About Jpeg Compression To set preferences Setting PreferencesVisioneer Onetouch 8820 Scanner Installation Guide Configuring the Scanner Scanning from the Paperport Software To set up the PaperPort software with the scannerTo scan an item Scanning AN Item with the Twain ButtonClick AutoScan to scan with your preset scan choices To scan manually To scan automatically Click AutoScan Getting Help with the Paperport Software To adjust a setting Adjusting the Settings on the Scan Manager PROTo save a new proﬁle Saving a NEW ProfileVisioneer Onetouch 8820 Scanner Installation Guide Adjusting the Resolution and Sharpness To use the advanced options To adjust the resolution and sharpnessTo adjust the brightness and contrast Adjusting the Brightness and ContrastTo use the Sampler buttons Adjusting GAMMA, SATURATION, and Color HUE To adjust the color settings Adjusting Output Size To manually set the output size for an item To Auto Trim an item Click Auto TrimAdjusting the Settings on the Scan Manager PRO Area you selected to scan Saving a Custom Size To save a custom size settingScan Info BOX Zooming in and OUTTo enlarge and reduce the preview image To set the Scan Manager Pro preferences Getting Help with the Scan Manager PRO To see the Scan Manager Pro help information Cleaning the Scanner GlassScanner dimensions Scanning resolutionWeight Operating temperatureD E Page Index