DLP
LED Error Messages
| ERROR CODE MESSAGES |
|
| POWER LED |
|
| READY LED |
|
| TEMP LED |
|
|
|
| BLINK |
|
| BLINK |
|
| BLINK |
| |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| Over temperature |
|
| OFF |
|
| OFF |
|
| ON |
|
|
|
|
|
|
|
|
|
|
|
| |
| Thermal Break |
| 4 |
|
| OFF |
|
| OFF |
| |
|
|
|
|
|
|
|
|
|
| ||
| G794 fail |
| 4 |
| 4 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| T1 fail |
| 4 |
| 5 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
|
| |
| Lamp error |
| 5 |
|
| OFF |
|
| OFF |
| |
|
|
|
|
|
|
|
|
|
| ||
| Ballast Over Temperature |
| 5 |
| 1 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Ballast shot circuit in output detected |
| 5 |
| 2 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| End of lamp lift detected |
| 5 |
| 3 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Ballast lamp did not ignite |
| 5 |
| 4 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp extinguished during normal operation |
| 5 |
| 5 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp extinguished during |
| 5 |
| 6 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp Memory write error |
| 5 |
| 7 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp Memory write buffer overflow |
| 5 |
| 8 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp UART buffer overflow |
| 5 |
| 9 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp current calculation error |
| 5 |
| 10 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp Corrupted software configuration |
| 5 |
| 11 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp voltage too low |
| 5 |
| 12 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp FLASH memory CRC error |
| 5 |
| 13 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp EEPROM memory CRC error |
| 5 |
| 14 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Lamp EEPROM configuration does not match FLASH kernel |
| 5 |
| 15 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Fan1 error (Lamp Fan) |
| 6 |
| 1 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Fan2 error (Ballast Fan) |
| 6 |
| 2 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Fan3 error (Burner Fan) |
| 6 |
| 3 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
| ||
| Fan4 error (Power Fan) |
| 6 |
| 4 |
|
| OFF |
| ||
|
|
|
|
|
|
|
|
|
|
| |
| Lamp door open |
| 7 |
|
| OFF |
|
| OFF |
| |
|
|
|
|
|
|
|
|
|
|
| |
| DMD error |
| 8 |
|
| OFF |
|
| OFF |
| |
|
|
|
|
|
|
|
|
|
|
| |
| Color wheel error |
| 9 |
|
| OFF |
|
| OFF |
| |
|
|
|
|
|
|
|
|
|
|
|
|
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re- starting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact your service center.
Image Problems
Problem: No image appears on the screen
1.Verify the settings on your notebook or desktop PC.
2.Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1.Adjust the Focus on the projector.
2.Press the Auto button on the remote control or projector.
– 46 –