Vivitek D935VX, D930TX manual Lamp Problems, Remote Control Problems, Problem The image is reversed

Page 53
Problem: The image is wider at the top or bottom (trapezoid effect)

DLP Projjecttor – User’s Manuall

3.Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.

4.Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

1.Position the projector so it is as perpendicular to the screen as possible.

2.Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Installation I menu of the OSD.

Problem: The image is streaked

1.Set the Frequency and Tracking settings on the Computer menu of the OSD to the de- fault settings.

2.To ensure the problem is not caused by a connected PC’s video card, connect to another computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Image menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1.Check that the power cable is securely connected.

2.Ensure the power source is good by testing with another electrical device.

3.Restart the projector in the correct order and check that the Power LED is green.

4.If you have replaced the lamp recently, try resetting the lamp connections.

5.Replace the lamp module.

6.Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1.Power surges can cause the lamp to turn off. Re-plug power cord. When the READY LED is on, press the power button.

2.Replace the lamp module.

3.Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1.Direct the remote control towards remote sensor on the projector.

2.Ensure the path between remote and sensor is not obstructed.

3.Turn off any fluorescent lights in the room.

4.Check the battery polarity.

5.Replace the batteries.

6.Turn off other Infrared-enabled devices in the vicinity.

7.Have the remote control serviced.

47

Image 53
Contents Trademark Recognition CopyrightDisclaimer Symbols Used Important Safety InformationGeneral Safety Information DLP Projjecttor-User’s ManuallPreface Projector Installation NoticePower Safety Cleaning the Projector Main FeaturesSymbol Explanations About this manualSETUP AND OPERATION Table of ContentsON-SCREEN DISPLAY OSD MENU SETTINGS MAINTENANCE AND SECURITYREGULATORY COMPLIANCE SPECIFICATIONSGETTING STARTED Packing ChecklistDLP Projjecttor - User’s Manuall Avoid using the projector in dusty environmentsD930TX does not have the zoom ring D935VX / D940VX / D930TX Front-right ViewViews of Projector Parts see LED Error Messages on page Top view-On-screen Display OSD buttons and LEDsRear view When installing, ensure that you use only UL Listed ceiling mounts Bottom viewRemote Control Parts LABEL Projector and Remote Control Buttons Remote Control Operating RangeInserting the Remote Control Batteries SETUP AND OPERATION1. Only use AAA batteries Alkaline batteries are recommended 2. Dispose of used batteries according to local ordinance regulationsConnecting Input Devices Starting and Shutting down the Projector 1. Be sure to remove the lens cap before starting projector Security Lock Setting an Access Password Security LockService center will validate the owner and help reset the password The projector table or stand should be level and sturdy Adjusting the Projector LevelPosition the projector so that it is perpendicular to the screen Ensure the cables are in a safe location. You could trip over them4. The keystone control appears on the display Adjusting the Zoom ring VX Series only, Focus and Keystone1. Press the Volume +/- buttons on the remote control Adjusting the VolumeOSD Menu Controls ON-SCREEN DISPLAY OSD MENU SETTINGSNavigating the OSD Set the OSD language to your preference before continuing Setting the OSD Language2. Press the cursor button until Language is highlighted 4. Press the MENU button twice to close the OSDOSD Menu Overview OSD Sub-Menu Overview Image Menu Advanced Feature Press Enter / to enter the Color Manager sub menu Color ManagerComputer Menu Video/Audio Menu Press Enter / to enter the Audio sub menu AudioInstallation I Menu Installation II Menu DLP Projjecttor-User’s Manuall Peripheral Test OSD Menu SettingNetwork Lamp Hour ResetTo connect to a network LAN, refer to the following steps The Projector Web Server home page displays. In the example, the projector resides at IP address 3. Right-click on Local Area Connection, and select Properties 2. On the PC Laptop, select Start´ Control Panel´ Network Connections5. Click Properties DLP Projjecttor - User’s Manuall DLP Projjecttor-User’s Manuall Status Factory Resetb. Do not dispose this product with general household waste MAINTENANCE AND SECURITYReplacing the Projection Lamp r - User’s Manual Resetting the Lamp Cleaning the Case Cleaning the LensCleaning the Projector 1. Do not use abrasive cleaners or solventsUsing the Kensington Lock Tips for Troubleshooting TROUBLESHOOTINGCommon problems and solutions Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsProblem The image is wider at the top or bottom trapezoid effect Problem The image is reversedHaving the Projector Serviced Audio ProblemsProblem There is no sound Problem The sound is distortedSpecifications SPECIFICATIONSD935VX D940VXProjection Distance vs. Projection Size D935VX / D940VX / D930TX Projection Distance and Size TableD935VX D940VXH-SYNC D935VX / D940VX / D930TX Timing Mode TableV-SYNC S-VIDEODLP Projector-User’s Manual Projector Dimensions REGULATORY COMPLIANCE Safety CertificationsFCC Warning Canada