Vivitek D7 user manual DLP Projector - User’s Manual

Page 22

The service center will validate the owner and help reset the password.

DLP Projector – User’s Manual

5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five.

Press the cursor buttons in any order to set the password. Push the MENU button to exit the dialog box.

6. The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled.

Enter the password in the order you set it at step 5. In case you forget the password, please contact the service center.

The service center will validate the owner and help reset the password.

– 14 –

Image 22

Contents 用户手册 D7 Series用戶手冊 사용자 설명서Disclaimer CopyrightTrademark Recognition General Safety Information Important Safety InformationSymbols Used DLP Projector - User’s ManualProjector Installation Notice PrefaceSymbol Explanations Power SafetyCleaning the Projector Replacing the LampMain Features About this ManualON-SCREEN DISPLAY OSD MENU SETTINGS Table of ContentsSETUP AND OPERATION MAINTENANCE AND SECURITYSPECIFICATIONS REGULATORY COMPLIANCEGETTING STARTED Packing ChecklistAvoid using the projector in dusty environments LABEL Front-right ViewViews of Projector Parts DESCRIPTIONRear view 56.00 Bottom viewWhen installing, ensure that you use only UL Listed ceiling mounts 146.00Remote Control Parts Changes settings in the OSD Remote Control Operating Range Projector and Remote Control Buttons1. Only use AAA batteries Alkaline batteries are recommended SETUP AND OPERATIONInserting the Remote Control Batteries 2. Dispose of used batteries according to local ordinance regulationsA B C D E F G Connecting Input DevicesL K J ！Warning Starting and Shutting down the Projector DLP Projector - User’s Manual Setting an Access Password Security Lock Security LockThe service center will validate the owner and help reset the password Adjusting the Projector Level Adjusting the Keystone VolumeAdjusting the Volume 1. Press the Volume +/- buttons on the remote controlNavigating the OSD ON-SCREEN DISPLAY OSD MENU SETTINGSOSD Menu Controls 4. Press the MENU button twice to close the OSD Setting the OSD Language2. Press the cursor button until Language is highlighted Set the OSD language to your preference before continuingOSD Menu Overview OSD Sub-Menu Overview Image Menu Advanced Feature Color Manager Press Enter / to enter the Color Manager sub menuComputer Menu Video/Audio Menu Audio Press Enter / to enter the Audio sub menuInstallation I Menu Presentation Timer Installation II Menu DLP Projector - User’s Manual OSD Menu Setting Peripheral TestLamp Hour Reset Network LANRJ45 3. Right-click on Local Area Connection, and select Properties 5. Click Properties8. Select Installation II → Advanced→ Network CATEGORY INPUT -LENGTHFactory Reset StatusReplacing the Projection Lamp MAINTENANCE AND SECURITYb. Do not dispose this product with general household waste Remove the two screws from the lamp module Lift the module handle up Resetting the Lamp Cleaning the Projector Cleaning the LensCleaning the Case 1. Do not use abrasive cleaners or solventsUsing the Security Chain Lock Using the Kensington LockUsing the Physical Lock Common problems and solutions TROUBLESHOOTINGTips for Troubleshooting Problem No image appears on the screen LED Error MessagesImage Problems Problem The image is blurredAudio Problems Lamp ProblemsRemote Control Problems Having the Projector ServicedQ. How do I run HDMITM cables longer than 10 meters? HDMITM Q & AQ. How can I tell if a cable is an HDMITM certified cable? SPECIFICATIONS SpecificationsD795WT Projection Distance and Size TableProjection Distance vs. Projection Size WXGAV-SYNC Timing Mode TableH-SYNC HDMITMO Frequency supported - Frequency not supported 319.00 Projector Dimensions411.00 354.00FCC Warning Safety CertificationsREGULATORY COMPLIANCE Canada201009