Runco DTV-992 manual Start up with full white image, Signal Input Connection to the Projector

Page 13

Connections

When starting up the projector, with the power switch or via the stand-by key, the projector can start up in two ways if the “CRT run in” cycle option is switched OFF.

-full white image (projector warm up) or

-immediately image display.

The way of starting up can be set in the service mode.

Start up with full white image.

The next menu will be displayed for 30 seconds.

a. Start up with warm up period.

If no action is taken, a white image will be displayed for 20 min- utes.

This white image will be shifted on the faceplate of the CRT to avoid burn in. During this warm up period, it is possible to interrupt this white image projection by pressing the EXIT key. The previous menu will be repeated for another 30 seconds but the remaining time will be indicated.

If EXIT is pressed, the remaining warm up period will be shipped.

During the warm up period, every 30 seconds a text box with the remaining time will be displayed on the screen for 2 seconds. This text box will be displayed every time on another place.

If another key, different from EXIT, is pressed, a text box with fol- lowing text will be displayed:

Please use <EXIT> to leave this procedure.

b. Start up without warm up period.

If the EXIT key is pressed, the warm up period will be skipped and the projector is immediately ready for use.

Warning : skipping this warm up procedure can reduce the initial picture quality of the projected image.

Signal Input Connection to the Projector:

-Composite Video

-S-Video

-RGBS or RGsB

-RGB3S or RG3sB (option)

PROJECTOR WARM UP

A FULL WHITE PATTERN WILL BE GENERATED FOR 20 MINUTES

FOR IMMEDIATE USE OF THE PROJECTOR, PRESS <EXIT>

WARNING: SKIPPING THIS PROCEDURE CAN REDUCE THE INITIAL PICTURE QUALITY OF THE PROJECTED IMAGE.

THIS OPTION CAN BE

DISABLED IN THE SERVICE

MENU

REMAINING PROJECTOR WARM UP TIME

18.5 MIN

PLEASE USE

<EXIT> TO

LEAVE THIS

PROCEDURE

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

Comm Port

Port 3

R

G

B Comp/ VSYNC

VIDEO

Green=Oper.

Off On

 

 

 

HSYNC

 

Red=Stby

Power/Mains

 

 

 

 

 

 

 

 

 

 

 

 

 

Port No.

Projector Input

Press Digit Button

 

 

 

1

Not Used

Not Used

2

Not Used

Not Used

3

RGB2

3

 

4/5

RGB2

4 or 5

4/5

Component Video3

6

 

 

 

 

 

 

 

4/5

RGB with Tri-Level Sync4

7

 

 

4/5

Component Video

 

 

 

 

with Tri-Level Sync5

8

 

 

 

 

 

 

3

4

5

2

1

1Not Used

2Not Used

3Input signal : R-Y, Y and B-Y with separate composite sync or with separate Hor and Vert. sync or with composite sync on Y.

4Input signal : R, G and B with separate Tri level sync or with Tri-level sync on green.

5Input signal : R-Y, Y and B-Y with separate Tri level sync or with composite Tri-level sync.

*Video or S-Video : switchable in the Picture Tuning menu.

Only available when the optional Tri-level sync module is installed.

3-2

Page 12 Page 14
Image 13
Page 12 Page 14
Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev

DTV-992 specifications

The Runco DTV-992 is a high-performance DLP projector that has garnered attention for its superior image quality and advanced features, making it a popular choice among home theater enthusiasts and professionals alike. With a focus on delivering an exceptional viewing experience, the DTV-992 showcases Runco's commitment to innovation and excellence in display technology.

One of the standout features of the DTV-992 is its impressive resolution. The projector supports full HD 1080p, allowing for stunningly detailed images that bring content to life. This resolution, combined with the projector's high brightness output, ensures that it performs well even in well-lit environments, providing flexibility for various viewing conditions.

The DTV-992 incorporates advanced DLP (Digital Light Processing) technology, which enhances image clarity and color accuracy. This technology minimizes the issues associated with traditional LCD projectors, such as motion blurring or color distortion, resulting in an incredibly smooth and vibrant visual experience. The projector also supports a wide color gamut, ensuring that colors are rich and true to life, further enhancing the overall viewing experience.

In terms of installation and connectivity, the DTV-992 offers multiple input options, including HDMI and component video connections. This versatility allows it to seamlessly integrate with various sources, from Blu-ray players to gaming consoles. Additionally, it includes features such as lens shift and zoom, making it easier to position the projector within a room and tailor the image to the desired screen size.

Runco has also placed an emphasis on user-friendliness in the DTV-992. The projector includes an intuitive interface and remote control, allowing users to easily navigate settings and make adjustments. The integration of advanced image processing technologies further optimizes performance, providing enhanced sharpness and contrast for a more immersive viewing experience.

With a sleek and modern design, the DTV-992 fits well into any home theater setup, providing not only outstanding performance but also aesthetic appeal. Whether for movie nights, sports events, or gaming sessions, the Runco DTV-992 delivers a combination of stunning visuals and advanced features that elevate the home entertainment experience to new heights. Its cutting-edge technology, superior image quality, and user-friendly design make it a top contender in the high-end projector market.
Top Page Image Contents