Runco DTV-992 manual No Pattern Error, Status Reporting Forced Break, Status Forced break

Page 65

Appendix 2

NO PATTERN ERROR

After starting up the automatic convergence, the projector will start to calculate and locate 5 horizontal and 5 vertical lines which are used to divide the screen into 25 areas.

If the projector does not succeed in finding the pattern, it will try two time. If the two attempts fail, the projector will quit the process and display the Error menu.

The AUTOCONVERGENCE selection will be followed by the error window displaying the following possibilities.

Error occurred, please check:

the lens cap is removed

the lens of the camera is correctly focused;

the camera is correctly centered;

if hardware problems exist, do diagnostics;

the ambient light is too high;

the blanking adjustments are correct;

Press the <ENTER> button to start EYE-QTMdiagnos- tics (refer to page for full details on EYE-QTMdiagnos- tics, please note that this option may vary in selection with different projectors).

STATUS REPORTING FORCED BREAK

After starting up the automatic convergence, if unexpected trouble such as the interruption of source input occurs, the projector will quit the process and display the AUTOCON- VERGENCE menu on the screen.

The status line in the AUTOCONVERGENCE menu will dis- play the following message:

EYE-Q

 

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with

or

then <ENTER>.

<EXIT> to return

Error occurred

check :

*lenscap removed *focus camera *center camera *ambient light too high

*hardware problem : press <ENTER> to start diagnostics

*blanking adjustments are correct

Press <ENTER>. to start EYE-Q diagnostics or <EXIT> to return

Status: Forced break

The possible causes of such an error:

The source is disconnected during the convergence: On the screen a message “Source not available” will be displayed and projector waits until the source is recon- nected or selected;

Switching sources during the convergence:

After the source is available again, the AUTOCONVER- GENCE menu will be displayed the status line reporting “Forced Break.”

AUTOCONVERGENCE

ON CURRENT SOURCE:

ALIGN

 

ALIGN FROM MIDPOSITION

ON ALL SOURCES: (XX)

TOUCH-UP

ALIGN

 

ALIGN FROM MIDPOSITION

STATUS:

 

forced break

 

Select with

or

then <ENTER>.

<EXIT> to return

APX-14

Page 64 Page 66
Image 65
Page 64 Page 66
Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPort No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Blanking TOP Bottom Left Right Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksTotal Run Time Change passwordChange Language Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyReference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev

DTV-992 specifications

The Runco DTV-992 is a high-performance DLP projector that has garnered attention for its superior image quality and advanced features, making it a popular choice among home theater enthusiasts and professionals alike. With a focus on delivering an exceptional viewing experience, the DTV-992 showcases Runco's commitment to innovation and excellence in display technology.

One of the standout features of the DTV-992 is its impressive resolution. The projector supports full HD 1080p, allowing for stunningly detailed images that bring content to life. This resolution, combined with the projector's high brightness output, ensures that it performs well even in well-lit environments, providing flexibility for various viewing conditions.

The DTV-992 incorporates advanced DLP (Digital Light Processing) technology, which enhances image clarity and color accuracy. This technology minimizes the issues associated with traditional LCD projectors, such as motion blurring or color distortion, resulting in an incredibly smooth and vibrant visual experience. The projector also supports a wide color gamut, ensuring that colors are rich and true to life, further enhancing the overall viewing experience.

In terms of installation and connectivity, the DTV-992 offers multiple input options, including HDMI and component video connections. This versatility allows it to seamlessly integrate with various sources, from Blu-ray players to gaming consoles. Additionally, it includes features such as lens shift and zoom, making it easier to position the projector within a room and tailor the image to the desired screen size.

Runco has also placed an emphasis on user-friendliness in the DTV-992. The projector includes an intuitive interface and remote control, allowing users to easily navigate settings and make adjustments. The integration of advanced image processing technologies further optimizes performance, providing enhanced sharpness and contrast for a more immersive viewing experience.

With a sleek and modern design, the DTV-992 fits well into any home theater setup, providing not only outstanding performance but also aesthetic appeal. Whether for movie nights, sports events, or gaming sessions, the Runco DTV-992 delivers a combination of stunning visuals and advanced features that elevate the home entertainment experience to new heights. Its cutting-edge technology, superior image quality, and user-friendly design make it a top contender in the high-end projector market.
Top Page Image Contents