Runco DTV-992 manual Sending a Record single instruction

Page 49

APPENDIX 1

Sending a RECORD (single instruction)

A RECORD consists of 9 bytes of information in the following order:

STX, OFFS, ADR, CMD, DAT1, DAT2, DAT3, DAT4, CHKS

Where:

 

 

STX

- 02H

Make projector(s) listen for its (their) unique address.

OFFS

- (1-255)

Offset you choose so that none of the data or CMDs - 02H (STX).

 

 

Normally set the offset to 0.

ADRe

- (1-255)

Number corresponding to projector’s unique address (see dip switch setting).

 

 

If you are unsure of your projector’s address, set this to 0.

 

 

It will talk to your projector regardless of its address.

CMDe

- (1-255)

The command to be sent to the projector (see list of commands).

 

 

See command list for all possible functions.

DAT1e - (1-255)

Additional data to be sent (set to 0 if not used)

DAT2e - (1-255)

Additional data to be sent (set to 0 if not used)

DAT3e - (1-255)

Additional data to be sent (set to 0 if not used)

DAT4e

- (1-255)

Additional data to be sent (set to 0 if not used)

CHKSe - (ADR + CMD + DAT1 + DAT2 + DAT3 + DAT4) mod 256 - add everything and keep only 2 right most digits

Note: Bytes from ADR to CHKS are shown in bold with the suffix ‘e’ to indicate the offset is added before sending the byte.

APP-2

Page 48 Page 50
Image 49
Page 48 Page 50
Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev

DTV-992 specifications

The Runco DTV-992 is a high-performance DLP projector that has garnered attention for its superior image quality and advanced features, making it a popular choice among home theater enthusiasts and professionals alike. With a focus on delivering an exceptional viewing experience, the DTV-992 showcases Runco's commitment to innovation and excellence in display technology.

One of the standout features of the DTV-992 is its impressive resolution. The projector supports full HD 1080p, allowing for stunningly detailed images that bring content to life. This resolution, combined with the projector's high brightness output, ensures that it performs well even in well-lit environments, providing flexibility for various viewing conditions.

The DTV-992 incorporates advanced DLP (Digital Light Processing) technology, which enhances image clarity and color accuracy. This technology minimizes the issues associated with traditional LCD projectors, such as motion blurring or color distortion, resulting in an incredibly smooth and vibrant visual experience. The projector also supports a wide color gamut, ensuring that colors are rich and true to life, further enhancing the overall viewing experience.

In terms of installation and connectivity, the DTV-992 offers multiple input options, including HDMI and component video connections. This versatility allows it to seamlessly integrate with various sources, from Blu-ray players to gaming consoles. Additionally, it includes features such as lens shift and zoom, making it easier to position the projector within a room and tailor the image to the desired screen size.

Runco has also placed an emphasis on user-friendliness in the DTV-992. The projector includes an intuitive interface and remote control, allowing users to easily navigate settings and make adjustments. The integration of advanced image processing technologies further optimizes performance, providing enhanced sharpness and contrast for a more immersive viewing experience.

With a sleek and modern design, the DTV-992 fits well into any home theater setup, providing not only outstanding performance but also aesthetic appeal. Whether for movie nights, sports events, or gaming sessions, the Runco DTV-992 delivers a combination of stunning visuals and advanced features that elevate the home entertainment experience to new heights. Its cutting-edge technology, superior image quality, and user-friendly design make it a top contender in the high-end projector market.
Top Page Image Contents