Sim2 Multimedia D60 user manual Setup menu, Information menu

Page 39

		Menu Display Time (10 sec)
		Sets the length of time the OSD will remain active after your last key
	Menu Settings	press. The range is from 5 to 30 seconds in 5-second increments.
		Menu Position (Center)
		Sets the On-Screen Display (OSD) menu position.
	Input Source	Selects an input source to be projected. See "Selecting an input
	Input Source	source" on page 18 for details.
		source" on page 18 for details.
		Sets whether the projector searches automatically for input
	Auto Source Search	sources. If the source scan is Off, the projector will scan for input
	(Off)	sources until it acquires a signal. If the function is not activated, the
		projector selects the last used input source.

Setup menu

	FUNCTION	DESCRIPTION
	(default setting / value)	DESCRIPTION

		Lamp Power (Normal)
	Lamp settings	Selects the projector lamp between Normal and Whisper modes.
	Lamp settings	Lamp Hours
		Shows the lamp hours information. See "Getting to know the lamp
		hour" on page 43 for details.
		Grid
		Press ENTER to display the grid test pattern. It helps you adjust the
		image size and focus and check that the projected image is free of
	Pattern	distortion.
		Color Bar
		Press ENTER to display the color bar test pattern. You can display this
		test pattern to check that the colors are to your liking.
		Dust Filter Hours
	Dust Filter	Shows the dust filter hours information
	Dust Filter	Reset Dust Filter Timer
		Resets the duster filter timer to '0'. See "To clean the filter" on
		page 42 for details.
	High Altitude Mode	A mode for operation in areas like high altitude or high
	High Altitude Mode	temperature. See "Operating in a high altitude environment" on
	(Off)
	(Off)	page 31 for details.
		page 31 for details.
		Password (Off)
		Limits use of the projector to only those who know the correct
		password. See "Utilizing the password function" on page 20 for
	Password	details.
	Password	Change Password
		Change Password
		You will be asked to enter the current password before changing to
		a new one. See "Utilizing the password function" on page 20 for
		details.
		Returns all settings to the factory preset values.
	Reset All Settings	The following settings will still remain: the selected input source, the
	Reset All Settings	position of lens shift, names of user modes, Keystone, Phase, Language,
		Projector Position, Reset Dust Filter Timer, High Altitude Mode, and
		Password.

Information menu

This menu shows you the current operating status of the projector.

Using the projector 39

Image 39

Contents Page Table of contents Important safety instructions Ceiling mounting the projector Moisture condensationAvoid volatile liquid DisposalOverview Shipping contentsRemote control batteries Remote control operationProjector features Rear view Connector panelProjector exterior view Front and upper side viewFront and upper side view Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizePositioning your projector With min Position Inch Zoom Cm C Cm D Projection dimensionsInstallation for a 169 ratio screen Floor Installation Widescreen ratio screen dimension tableStandard ratio screen dimension table Installation for a 43 ratio screenBetter video quality Connecting with video equipmentPreparations Best video qualityConnecting Hdmi devices Connecting Rgbhv devicesConnecting component-video devices Connecting a computer Connecting S-Video or video devicesTurning the projector on Using the projectorUsing the remote control Using the OSD menuFine-tuning the image size and clarity Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Two parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionUsing the preset and user modes Selecting a picture modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture modeRenaming user modes Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsColor Management Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorSelecting the aspect ratio Adjusting contrast ratio via IrisAbout the aspect ratio Using anamorphic lenses optional To activate High Altitude ModeOperating in a high altitude environment RGB HD Displaying more than one image source simultaneouslyMy Screen Disabled functions for the active windowsCreating your own startup screen Personalizing the projector menu displayTurning the power off Color On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSetup SystemInformation Dynamic Black Image menuColor menu Brilliant ColorSleep Timer Display menuSystem menu Information menu Setup menuFunction Description Cleaning and replacing the dust filter Additional informationCare of the projector Resetting the filter timer To clean the filterLamp information Getting to know the lamp hourExtending lamp life Replacing the lamp Timing of replacing the lampOff on page 34 for details Indicators When the projector is in a normal stateWhen the projector is in an abnormal state Problem Cause Remedy TroubleshootingSpecifications Format Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for DVI-D and Hdmi Hdcp inputWarranty and Copyright information CopyrightDisclaimer MIC statement Regulation statementsFCC statement for United States users EEC statement for European users