Sim2 Multimedia D60 user manual Troubleshooting, Problem Cause Remedy

Page 47

Troubleshooting

Problem

Cause

Remedy

 

 

Plug the power cable into the AC inlet

 

 

on the rear of the projector, and plug

 

There is no power from the

the power cable into to the power

 

power cable.

outlet. If the power outlet has a

 

 

switch, make sure that it is switched

The projector does

 

on. (See page 18)

 

 

The power switch is not in the

Put the power switch in the on

not turn on.

on position.

position. (See page 18)

 

 

 

 

 

Attempting to turn the

Wait until the cooling down process

 

projector on again during the

 

has completed.

 

cooling process.

 

 

 

 

 

 

The lamp cover is not securely

Correctly attach the lamp cover. (See

 

attached.

page 44)

 

 

 

 

The video source is not turned

Turn the video source on and check

 

that the signal cable is connected

 

on or connected correctly.

 

correctly. (See page 15)

 

 

 

 

 

No picture.

The projector is not correctly

 

connected to the input source

Check the connection. (See page 15)

 

device.

 

 

 

 

 

The input signal has not been

Select the correct input signal with the

 

Source buttons on the remote control.

 

correctly selected.

 

(See page 18)

 

 

 

 

 

 

The connection cables are not

Correctly connect the cables to the

Image is unstable.

securely connected to the

appropriate terminals. (See page 15)

 

projector or the signal source.

 

 

 

 

 

 

The projection lens is not

Adjust the focus of the lens using the

Picture is blurred.

correctly focused.

focus ring. (See page 19)

 

 

The projector and the screen

Adjust the projection angle and

 

direction as well as the height of this

 

are not aligned properly.

 

unit if necessary. (See page 22)

 

 

 

 

 

 

The batteries are out of power.

Replace both of the batteries with

 

new ones. (See page 5)

 

 

Remote control

 

 

There is an obstacle between

 

does not work

the remote control and the

Remove the obstacle. (See page 5)

correctly

projector.

 

 

 

 

 

You are too far away from the

Stand within 8 meters (26.2 feet) of the

 

projector.

projector. (See page 5)

 

 

 

Additional information 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Page Table of contents Important safety instructions Ceiling mounting the projector Moisture condensationAvoid volatile liquid DisposalOverview Shipping contentsRemote control batteries Remote control operationProjector features Rear view Connector panelProjector exterior view Front and upper side viewFront and upper side view Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizePositioning your projector With min Position Inch Zoom Cm C Cm D Projection dimensionsInstallation for a 169 ratio screen Floor Installation Widescreen ratio screen dimension tableStandard ratio screen dimension table Installation for a 43 ratio screenBetter video quality Connecting with video equipmentPreparations Best video qualityConnecting component-video devices Connecting Hdmi devicesConnecting Rgbhv devices Connecting a computer Connecting S-Video or video devicesTurning the projector on Using the projectorUsing the remote control Using the OSD menuFine-tuning the image size and clarity Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Two parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionFine-tuning the selected picture mode Using the preset and user modesSelecting a picture mode Renaming user modes Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsColor Management Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorSelecting the aspect ratio Adjusting contrast ratio via IrisAbout the aspect ratio Operating in a high altitude environment Using anamorphic lenses optionalTo activate High Altitude Mode RGB HD Displaying more than one image source simultaneouslyMy Screen Disabled functions for the active windowsCreating your own startup screen Personalizing the projector menu displayTurning the power off Color On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsInformation SetupSystem Dynamic Black Image menuColor menu Brilliant ColorSystem menu Sleep TimerDisplay menu Information menu Setup menuFunction Description Care of the projector Cleaning and replacing the dust filterAdditional information Resetting the filter timer To clean the filterExtending lamp life Lamp informationGetting to know the lamp hour Replacing the lamp Timing of replacing the lampOff on page 34 for details When the projector is in an abnormal state IndicatorsWhen the projector is in a normal state Problem Cause Remedy TroubleshootingSpecifications Format Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for DVI-D and Hdmi Hdcp inputDisclaimer Warranty and Copyright informationCopyright MIC statement Regulation statementsFCC statement for United States users EEC statement for European users
Top Page Image Contents