Sim2 Multimedia D60 user manual Indicators, When the projector is in a normal state

Page 46

Indicators

There are three indicators which show the status of the projector. Check the following for information about the indicator lights. If there is anything wrong, turn the projector off and contact your dealer.

When the projector is in a normal state, ...

Lamp

Temp

Power

Status & Description

 

 

 

 

Red

Red

Red

Main power switch on

Off

Off

Orange

Stand-by mode

Off

Off

Green

Powering up

Flashing

 

 

 

Off

Off

Green

Normal operation

 

 

 

• The projector needs 90 seconds to cool down as it

 

 

Orange

was abnormally shut down without the normal

Off

Off

cooling down process.

 

 

Flashing

• The projector needs to cool for 90 seconds after the

 

 

 

 

 

 

power is turned off.

 

 

 

 

When the projector is in an abnormal state, ...

Lamp

Temp

Power

Status & Description

 

 

 

 

 

Red

Off

Off

• The lamp has been damaged. Please contact your

local customer center for purchasing a new lamp.

 

 

 

 

 

 

• The lamp is not properly attached.

Red

Off

Orange

• The lamp has been damaged. Please contact your

 

 

 

local customer center for purchasing a new lamp.

Off

Red

Off

 

 

Red

Red

Off

The fans are not working.

 

Green

Red

Off

 

 

 

Orange

Red

Off

 

The projector has shutdown

Red

Green

Off

Fan sensors error

automatically. If you try to

Orange

Green

Off

Fans do not rotate during

re-start the projector, it will

Red

Orange

Off

powering up.

shutdown again. Please

Red

Red

Red

 

 

contact your dealer for

Green

Red

Red

 

 

assistance.

Orange

Red

Red

Thermal condition error

 

Red

Red

Green

 

 

 

Green

Red

Green

 

 

Orange

Red

Green

 

 

Red

Red

Orange

The internal temperature is too high.

Green

Red

Orange

• The intake ventilation or the exhaust ventilation is

 

 

 

 

 

 

blocked.

 

Orange

Red

Orange

• The projector may be in a poorly ventilated location.

 

 

 

• The ambient temperature may be too high.

Green

Orange

Off

The dust filter is seriously clogged with dust. The projector

is going to shut down.

 

 

 

 

 

46 Additional information

Image 46
Contents Page Table of contents Important safety instructions Disposal Moisture condensationAvoid volatile liquid Ceiling mounting the projectorRemote control operation Shipping contentsRemote control batteries OverviewProjector features Front and upper side view Connector panelProjector exterior view Rear viewControls and functions Front and upper side viewRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Shifting the projection lens verticallyPositioning your projector Widescreen ratio screen dimension table Projection dimensionsInstallation for a 169 ratio screen Floor Installation With min Position Inch Zoom Cm C Cm DInstallation for a 43 ratio screen Standard ratio screen dimension tableBest video quality Connecting with video equipmentPreparations Better video qualityConnecting Rgbhv devices Connecting Hdmi devicesConnecting component-video devices Connecting S-Video or video devices Connecting a computerUsing the OSD menu Using the projectorUsing the remote control Turning the projector onUsing the menus Fine-tuning the image size and claritySetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Correcting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesSelecting a picture mode Using the preset and user modesFine-tuning the selected picture mode Resetting the picture mode Setting the User 1/User 2/User 3 modeRenaming user modes Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image claritySetting a preferred color temperature Color ManagementAdjusting Brilliant Color Selecting a Gamma settingAdjusting contrast ratio via Iris Selecting the aspect ratioAbout the aspect ratio To activate High Altitude Mode Using anamorphic lenses optionalOperating in a high altitude environment Displaying more than one image source simultaneously RGB HDPersonalizing the projector menu display Disabled functions for the active windowsCreating your own startup screen My ScreenTurning the power off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure ColorSystem SetupInformation Brilliant Color Image menuColor menu Dynamic BlackDisplay menu Sleep TimerSystem menu Setup menu Information menuFunction Description Additional information Cleaning and replacing the dust filterCare of the projector To clean the filter Resetting the filter timerGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Replacing the lampOff on page 34 for details When the projector is in a normal state IndicatorsWhen the projector is in an abnormal state Troubleshooting Problem Cause RemedySpecifications Timing chart Format Resolution Refresh rateHz Freq.KHz Pixel Freq.MHzSupported timing for DVI-D and Hdmi Hdcp input Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationDisclaimer EEC statement for European users Regulation statementsFCC statement for United States users MIC statement