AMD GA-M55S-S3 PCIE12V Power Connector, Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector

Page 20

English

3)PCIE_12V (Power Connector)

The PCIE_12V power connector supplies extra power to the PCIE x16 slot. Connect this connector depending on your system requirements.

1

Definition

PIin No.

1

NC

2

GND

3

GND

4

+12V

4/5/6) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Remember to connect the CPU/system/power fan cable to the CPU_FAN/SYS_FAN/PWR_FAN connector to prevent CPU damage or system hanging caused by overheating.

CPU_FAN

CPU_FAN

GA-M55S-S3 Motherboard

1

CPU_FAN

1

SYS_FAN

1 PWR_FAN

- 20 -

CPU_FAN :

Pin No.

Definition

1

GND

2

+12V / Speed Control

3

Sense

4

Speed Control

SYS_FAN / PWR_FAN :

 

 

Pin No.

Definition

1

GND

2

+12V

3

Sense

Only for PCB REV. 1.0. Only for PCB REV. 1.1.

Image 20
Contents GA-M55S-S3 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M55S-S3 Motherboard Layout GA-M55S-S3Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction LineLine Out Front Speaker Out MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi Spdif In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuBios Setting Recovery Main Menu For example Bios Ver. E6F12 For Boot Menu „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master/Slave Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryBoot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckAway Mode Integrated Peripherals IDE Prefetch Mode NV Sata 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip MAC LANOnboard LAN Boot ROM Parallel Port ModeOnboard Onboard Serial PortECP Mode Use DMA On-Chip USBUSB Keyboard Support USB Mouse SupportPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature Case OpenedCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Frequency MHz Pcie Clock MHzCPU Clock Ratio DDR2 Voltage ControlNormal CPU Vcore CPU HT-Link VoltageCPU Voltage Control Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES Appendix Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English Contact Us Taiwan HeadquartersGigabyte Global Service System