AMD GA-M55S-S3 user manual Nvidia

Page 72

English

After that, the Array List screen displaying the RAID array you created will appear (Figure 8).

If you want to set the disk array as boot device, use the UP or DOWN ARROW key to select the array and press B. The Boot section will show Yes.

 

 

MediaShield Utility

Mar

22 2006

 

 

 

 

- Array List -

 

Boot

Id

Status

 

Vendor

 

Array Model Name

No

2

Healthy

NVIDIA

STRIPE 223.57G

[Ctrl-X] Exit

[

] Select

[B] Set Boot

[N] New Array [ENTER] Detail

 

 

 

 

 

 

 

Figure 8

To read more information about the RAID array, press ENTER to enter the Array Detail screen (Figure 9), where you should see detailed information about RAID mode, disk block size, disk model name, and disk capacity, etc.

 

 

MediaShield Utility Mar 22 2006

 

 

 

 

- Array Detail -

 

RAID Mode: Striping

 

 

 

 

 

 

Striping Width : 1

 

 

 

 

Striping Block: 64K

 

Adapt

Channel

M/S

Index

Disk Model

Capacity

1

0

Master

0

 

ST3120026AS

111.79GB

1

1

Master

1

 

ST3120026AS

111.79GB

 

[R] Rebuild

[D] Delete

[C] Clear Disk [ENTER] Return

Figure 9

To delete the array, press D in the Array Detail screen. When the "Delete this array?" message appears, press Y to confirm or N to cancel. Press ENTER to return to the Array List screen.

To exit the Nvidia RAID utility, press ESC in the main menu or Ctrl+X in the Array List screen.

Now, you can proceed to install the SATA controller driver and operating system.

GA-M55S-S3 Motherboard

- 72 -

Image 72
Contents GA-M55S-S3 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M55S-S3 Motherboard Layout GA-M55S-S3Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction LineLine Out Front Speaker Out MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi Spdif In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E6 F12 For Boot MenuBios Setting Recovery „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Away ModeInit Display First Integrated Peripherals IDE Prefetch Mode NV Sata 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip MAC LANOnboard LAN Boot ROM Parallel Port ModeOnboard Onboard Serial PortECP Mode Use DMA On-Chip USBUSB Keyboard Support USB Mouse SupportPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 2 IRQ AssignmentPCI 1 IRQ Assignment Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature Case OpenedCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Frequency MHz Pcie Clock MHzCPU Clock Ratio DDR2 Voltage ControlCPU HT-Link Voltage CPU Voltage ControlNormal CPU Vcore Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES Appendix Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English Contact Us Taiwan HeadquartersGigabyte Global Service System