AMD GA-M51GM-S2G IDE Channel 2/3/4/5 Master, Drive a, Floppy 3 Mode Support for Japan Area

Page 33
No floppy drive installed
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-typehigh-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled).
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity. (Default value) 3.5 inch double-sided drive; 2.88M byte capacity.

IDE Channel 2/3/4/5 Master

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. Extended IDE Drive SATA devices setup. You can use one of two methods:

Auto

Allows BIOS to automatically detect SATA IDE devices during POST.

 

(Default value)

None

Select this if no SATA IDE devices are used and the system will skip the

 

automatic detection step and allow for faster system start up.

Access Mode

Use this to set the access mode for the hard drive. The two options are:

 

Large/Auto(default:Auto)

Capacity

Capacity of currently installed hard disk.

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.

Cylinder

Number of cylinders

Head

Number of heads

Precomp

Write precomp

Landing Zone

Landing zone

Sector

Number of sectors

Drive A

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None

360K, 5.25" 1.2M, 5.25"

720K, 3.5"

1.44M, 3.5" 2.88M, 3.5"

Floppy 3 Mode Support (for Japan Area)

Disabled

Normal Floppy Drive. (Default value)

Drive A

Drive A is 3 mode Floppy Drive.

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

English

- 33 -

BIOS Setup

Image 33
Contents GA-M51GM-S2G Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M51GM-S2G Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC883 Codec Feature SummaryŠ 1 Spdif In/Out connector Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionLine Line Out Front Speaker OutATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper Cdin CD In ConnectorUSB1 / FUSB2 Front USB Connector Faudio Front Audio Panel ConnectorCI Chassis Intrusion, Case Open PowerledClrcmos Clear Cmos Spdifio Spdif In/Out 16 F11394 / F21394 Ieee 1394 ConnectorComb Comb Connector English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F2„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave TimeIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan AreaDrive a Halt onBase Memory MemoryExtended Memory Total MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek HDD S.M.A.R.T. Capability Password CheckInit Display First Frame Buffer SizeIntegrated Peripherals USB ConfigurationOn-Chip IDE Channel1 On-Chip IDE Channel0On-Chip USB USB Keyboard SupportSmart LAN LAN Cable Diagnostic Function Onboard LAN Boot ROMOnboard 1394 Function Parallel Port ModeOnboard Serial Port Onboard Parallel PortPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On By Keyboard Power On By MouseKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPCI 2 IRQ Assignment CPU Warning Temperature Current System/CPU TemperatureCurrent VoltageV Vcore / DDR18V / +3.3V / +12V Current System/CPU FAN Speed RPMSystem Smart FAN Control CPU Smart FAN ModeLoad Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Before you begin SATA-II Primary RAID Disabled SATA-II 2 Secondary RAID Nvidia Mirror Step Save and exit Bios Setup GA-M51GM-S2G Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata controller driver disk Cd bootdrv MenuInstalling Sata controller dr7iver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft Windows1NO .0.M English 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Sound Effect Configuration Troubleshooting English English English Taiwan Headquarters Contact UsChina Shanghai