AMD GA-M61PM-S2 user manual I/O Back Panel Introduction

Page 17

1-6 I/O Back Panel Introduction

English

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COMA (Serial Port)

Connects to serial-based mouse or data processing devices.

VGA Port

Monitor can be connected to VGA port.

IEEE 1394a Port

Serial interface standard set by the Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug.

USB Port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet , providing data transfer speeds of 10/100/ 1000Mbps.

Center/Subwoofer Speaker Out

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to Center/Subwoofer Speaker Out jack.

Surround Speaker Out (Rear Speaker Out)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be connected to Surround Speaker Out (Rear Speaker Out) jack.

Side Speaker Out

The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out jack.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

- 17 -

Hardware Installation

Image 17
Contents GA-M61PM-S2 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M61PM-S2 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerLAN Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction MIC Connectors IntroductionLine Out Front Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors IDE IDE ConnectorFaudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector13 F11394 / F21394 Ieee 1394 Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorSpdifio Spdif In/Out Connector Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery Main Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D1F12 Boot Menu „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime DateIDE Channel 0 Master/Slave IDE Channel 2, 3, 4, 5 MasterDrive a Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek AMD K8 Cool&Quiet controlInit Display First Password CheckNV Sata RAID function Serial-ATA RAID ConfigNV Sata 1 Primary RAID NV Sata 1 Secondary RAIDOnBoard LAN Boot ROM IDE Prefetch ModeNV Sata 2 Primary RAID NV Sata 2 Secondary RAIDECP Mode Use DMA Parallel Port ModeOnboard Parallel Port On-Chip USBAcpi Suspend Type Soft-Off by Power buttonPnP/PCI Configurations Reset Case Open Status CPU Smart FAN Mode Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two Press Y on your keyboard to load defaultsFlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer Shadow Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES BBS Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English Taiwan Headquarters Contact UsGigabyte Global Service System