Agilent Technologies U2751A manual Regulatory Markings

Page 6

Regulatory Markings

 

The CE mark is a registered trademark

 

The C-tick mark is a registered

 

of the European Community. This CE

 

trademark of the Spectrum

 

mark shows that the product complies

 

Management Agency of Australia.

 

with all the relevant European Legal

 

This signifies compliance with

 

Directives.

 

the Australia EMC Framework

 

 

 

regulations under the terms of the

 

 

 

Radio Communication Act of 1992.

 

 

 

 

 

ICES/NMB-001 indicates that this

 

This instrument complies with the

 

ISM device complies with the

 

WEEE Directive (2002/96/EC)

 

Canadian ICES-001.

 

marking requirement. This affixed

 

Cet appareil ISM est confomre a la

 

product label indicates that you must

 

norme NMB-001 du Canada.

 

not discard this electrical/electronic

 

 

 

product in domestic household waste.

 

 

 

 

 

The CSA mark is a registered

 

 

 

trademark of the Canadian Standards

 

 

 

Association.

 

 

 

 

 

 

VI

U2751A User’s and Service Guide

Image 6
Contents User’s and Service Guide U T I O N WA R N I N G Safety Symbols CATFrom occurring Instrument and accessories. The cables or wires should beAny other volatile liquid to clean the device Device protection may be impairedEnvironmental Conditions U T I O NRegulatory Markings Product Category Affixed product label is as shown belowFor more information This Guide… Getting StartedU2751A User’s and Service Guide Declaration of Conformity DoC T EContents Chassis Installation List of Figures U2922A pin configurationPin backplane connector pin configuration Panel view of the Agilent Measurement ManagerXIV Electrical and mechanical specifications update per List of TablesPart number and description of replaceable part XVI Chassis Installation InstallationU2751A DSub Connector IntroductionIntroduction Product at a Glance Product OutlookBumpers USB indicator Power indicator DSub connector Pin backplane connector USB inletPower inlet 105.00 mm 175.00 mm Product DimensionsDimensions Without Bumpers 25.00 mmDimensions With Bumpers 117.00 mm 180.00 mm41.00 mm Standard Purchase Items Initial Inspection Inspection and MaintenanceGeneral Maintenance Electrical CheckInstallation and Configuration InstallationWith Agilent VEE Pro, LabVIEW, or Microsoft Visual Studio Check Your System Hard-disk space 1 GBInstall the IO Libraries Suite Install the Module Driver Install the Agilent Measurement Manager T E Connect the Module to Your PC ProceedingGetting Started Select Ignore to disable the warning message Go to Start Control Panel and double-clickSystemGetting Started T E Send Commands To This Instrument Verify Your Module ConnectionIO Control will launch automatically when you start your PC Launch Your Agilent Measurement ManagerAgilent Measurement Manager help file U2751A DSub Connector 1Pin assignments2U2922A pin configuration U2922A Terminal BlockFemale DSub connector Terminal block Retractable cover 3U2922A outlook85.00 mm 85.00 mm 23.00 mm90.00 mm 105.00 mm 105.00 mm 23.00 mmU2922A Terminal Block Installation Prior to attaching the U2922A to the U2751ACables Housing Jack screws of the U2922APin Backplane Connector Pin Configuration DescriptionChassis Installation Power Up Switch Control Scpi Commands for System-Related TasksPower Up Switch Control 1Switch matrix conceptAgilent Measurement Manager Operation Scpi Commands Relay Cycle Counter 3Panel view of the relay cycle counterError Conditions System-Related OperationSelf-Test Scpi Commands for System-Related Tasks Example 4, Performing system-related tasksCharacteristics and Specifications Product Characteristics Operating EnvironmentProduct Specifications General characteristics Service Information Checking Defective Relays Row ColumnReplaceable Parts 2Part number and description of replaceable partDisassembly Instructions DIAGnosticRELayCYCLesCLEar @chlist Reassembly Instructions Contacting Agilent TechnologiesIndex Index Contact us