Agilent Technologies U2751A manual U2922A Terminal Block Installation, Cables

Page 43

Getting Started

1

U2922A Terminal Block Installation

This section provides the recommended procedure for connecting the U2922A terminal block to the U2751A.

	WA R N I N G	• The maximum working voltage of the U2751A with the
	WA R N I N G	terminal block for standalone is 35 Vrms and for
		terminal block for standalone is 35 Vrms and for
		modular (when used with the U2781A) is 180 Vrms.
		• The maximum transient voltage is 300 Vrms.
		• Do not remove the retractable cover from the U2922A
		terminal block during operation to avoid any
		unexpected hazard.

• You are required to connect the cables to the U2922A terminal block

N O T E

prior to attaching the U2922A to the U2751A.

•Ensure that you power-off your device and unplug the U2922A from the U2751A to change the cable connection on the U2922A.

Connect the cables to the terminal block as desired.

cables

U2751A User’s and Service Guide

27

Image 43

Contents User’s and Service Guide U T I O N WA R N I N G CAT Safety SymbolsDevice protection may be impaired Instrument and accessories. The cables or wires should beAny other volatile liquid to clean the device From occurringU T I O N Environmental ConditionsRegulatory Markings Affixed product label is as shown below Product CategoryFor more information Getting Started This Guide…U2751A User’s and Service Guide T E Declaration of Conformity DoCContents Chassis Installation Panel view of the Agilent Measurement Manager U2922A pin configurationPin backplane connector pin configuration List of FiguresXIV List of Tables Electrical and mechanical specifications update perPart number and description of replaceable part XVI Introduction InstallationU2751A DSub Connector Chassis InstallationIntroduction Product Outlook Product at a GlanceBumpers Pin backplane connector USB inlet USB indicator Power indicator DSub connectorPower inlet 25.00 mm Product DimensionsDimensions Without Bumpers 105.00 mm 175.00 mm117.00 mm 180.00 mm Dimensions With Bumpers41.00 mm Standard Purchase Items Electrical Check Inspection and MaintenanceGeneral Maintenance Initial InspectionInstallation Installation and ConfigurationWith Agilent VEE Pro, LabVIEW, or Microsoft Visual Studio Hard-disk space 1 GB Check Your SystemInstall the IO Libraries Suite Install the Module Driver Install the Agilent Measurement Manager T E Proceeding Connect the Module to Your PCGetting Started Go to Start Control Panel and double-clickSystem Select Ignore to disable the warning messageGetting Started T E Verify Your Module Connection Send Commands To This InstrumentLaunch Your Agilent Measurement Manager IO Control will launch automatically when you start your PCAgilent Measurement Manager help file 1Pin assignments U2751A DSub ConnectorU2922A Terminal Block 2U2922A pin configuration3U2922A outlook Female DSub connector Terminal block Retractable cover105.00 mm 23.00 mm 85.00 mm 23.00 mm90.00 mm 105.00 mm 85.00 mmPrior to attaching the U2922A to the U2751A U2922A Terminal Block InstallationCables Jack screws of the U2922A HousingDescription Pin Backplane Connector Pin ConfigurationChassis Installation Scpi Commands for System-Related Tasks Power Up Switch ControlPower Up 1Switch matrix concept Switch ControlAgilent Measurement Manager Operation Scpi Commands 3Panel view of the relay cycle counter Relay Cycle CounterSystem-Related Operation Error ConditionsSelf-Test Example 4, Performing system-related tasks Scpi Commands for System-Related TasksCharacteristics and Specifications Operating Environment Product CharacteristicsProduct Specifications General characteristics Service Information Row Column Checking Defective Relays2Part number and description of replaceable part Replaceable PartsDisassembly Instructions DIAGnosticRELayCYCLesCLEar @chlist Contacting Agilent Technologies Reassembly InstructionsIndex Index Contact us