Disclaimer, Power Supply, Power/LED Connections

Disclaimer

This manual is intended only as a guide for Antec's Computer Enclosures. For more comprehensive instructions on installing your motherboard and peripherals, please refer to the user's manuals which come with your components and drives.

SLK3700AMB - Super Mid Tower Case

Power Supply

The power supply installed in this case comes with a main power switch. Make sure you turn the switch to the ON ( I ) position before you boot up your computer for the first time. In normal operation there is no need to turn the switch to the OFF (O) position since the power supply is equipped with a soft on/off feature which turns your computer on and off through the soft switch on your computer case. You may occasionally need to turn the switch to the OFF position should your computer crash and you cannot shut it down through use of the soft switch.

[Applicable only to models designed for sale in the European Union: Solution power supply models designed for the EU include Power Factor Correction (PFC) circuitry in accord with European standard regulation code EN61000-3-2. By altering the input current wave shape, PFC improves the power factor of the power supply and results in increased energy efficiency, reduced heat loss, prolonged life for power distribution and consumption equipment, and improved output voltage stability.]

Note (not applicable to models designed for the European Union): Check the red power supply voltage switch setting before installation. It should be the same as your local power voltage (115V for North America, Japan, etc. and 230V in Europe and many other countries). Change the voltage setting if necessary. Failure to take this precaution could result in damage to your equipment and could void your warranty.

Set Up

1.Take the case out of the box.

2.Remove the Styrofoam.

3.Remove the plastic bag.

4.Place the case upright on a stable flat surface with the power supply fan at the back facing you .

5.Remove the screws from the right side panel.

6.There are two latches on the side panel. Press the latch release on each. The latches will pop up to about 65 degrees. Push the latches out to the 90 degree position to fully disengage the latches and swing open the panel.

7.Inside the case you should see the power supply, some wiring with marked connectors (USB, PWR etc.), an installed I/O panel, a power cord. You will also find a bag of hardware (drive rails, screws, brass standoffs, plastic stands, etc.)

8.Place the case with the front bezel facing you and press the release tabs on the bottom of the bezel to remove the front bezel. Set the bezel aside in a safe place.

Motherboard Installation

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult your motherboard manual for specific mounting instructions and troubleshooting.

1.Lay the case down so that the open side is up. You should be able to see the drive cage and power supply.

2.Make sure you have the appropriate I/O panel for your motherboard. If the panel provided is not suitable for your motherboard, please contact your motherboard manufacturer for the correct I/O panel.

3.Line up motherboard with the standoff holes, and determine which ones line up and remember where they are. Not all motherboards will match with all of the provided screw holes, and this is not necessary for proper functionality. (In other words there will likely be extra holes.) Some standoffs may be pre-installed for your convenience.

4.Lift up and remove your motherboard.

5.Screw in the brass standoffs to the threaded holes that line up with your motherboard.

6.Place your motherboard on the brass standoffs.

7.Screw in your motherboard to the standoffs with the provided Phillips-head screws.

8.Your motherboard is now installed.

Power/LED Connections

The Antec Solution Series SmartPower power supply is an ATX12V form factor power supply. An ATX12V power supply has a single 20-pin Main Power Connector, a 6-pin AUX Power Connector, and a 4-pin +12V Power Connector for the motherboard. It also comes with five to seven 4-pin Peripheral Power Connectors and one to two 4-pin Floppy Drive Power Connectors for your drives. It is backwards compatible to previous ATX form factor power supplies. If your motherboard does not support the AUX Power Connector or the +12V Power Connector, you can still use this power supply.

The power supply is also equipped with a 3-pin fan signal connector. Connect it to one of the fan connectors on your motherboard. You may monitor the speed of the rear power supply fan through your motherboard BIOS or through the monitoring software that comes with your motherboard. Note: The speed of the fan may be as low as 1500 RPM when temperatures are low. At these speeds some motherboards may not be able to properly detect the fan speed and may generate false warnings of fan failure. Please refer to your motherboard manual for proper fan monitoring set up.

1.Connect the 20-pin ATX power connector (and AUX or +12V connectors if appropriate) to your motherboard.

2.Reset switch (labeled RESET SW) connects to your motherboard at the RST connector. The label should be facing the front of the case, and for all of the following connectors as well.

3.Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard.

4.Speaker connector (labeled SPEAKER) is behind the PWR connector.

5.The Power LED, Hard Drive LED, and LED I & LED II connectors all share a single ribbon cable. Attach the Power LED (labeled POWER) and HDD LED connectors to the appropriate headers on your motherboard. The LED I and LED II connectors may be used as you see fit for such purpose as SCSI LED, Message LED, etc. as supported by your motherboard, expansion cards, and peripherals.

USB Connection

There are 8 wires with connectors coming from the front mounted USB ports of the case.

1.Locate the internal USB header on your motherboard. It consists of 10-pins in two rows.

Note: On some motherboards one or two pins may be marked as NC. This indicates no contact. It is an empty pin. You don't need to use it. On some motherboards one pin may be missing on either one or both rows. Don't worry about it. You only need 8 pins to connect to.

SLK3700AMB specifications

The Antec SLK3700AMB is a well-regarded mid-tower computer case known for its balance of features, design, and performance. Launched in the early 2000s, it quickly gained popularity among enthusiasts and general users alike, thanks to its blend of functionality and style.

One of the standout features of the SLK3700AMB is its spacious interior, which can accommodate a variety of motherboard sizes, including ATX and Micro-ATX formats. This flexibility makes it an appealing choice for builders who want a customizable setup. With ample room for up to six expansion slots, users can easily fit multiple graphics cards and other add-on cards for enhanced gaming and productivity.

Cooling is a significant concern for any build, and the SLK3700AMB impresses with its cooling solutions. It comes pre-installed with two 120mm fans, one located at the rear and another at the front. The case is designed to facilitate excellent airflow, which is critical for maintaining optimal temperatures, especially under heavy loads. Additionally, the case supports further cooling options, allowing enthusiasts to add more fans if needed.

The SLK3700AMB is also known for its sound-dampening features. The case is lined with soundproof materials that help reduce noise from components operating inside. This design makes it suitable for users who prioritize a quiet computing environment, such as those working with audio or video editing.

Aesthetically, the SLK3700AMB showcases a sleek and minimalistic design. The black finish combined with a silver front bezel gives it a professional and modern appearance, appealing to a wide range of users. The front panel features easily accessible USB ports and audio jacks for convenience, allowing quick connections for peripherals.

Cable management is another notable characteristic of the SLK3700AMB. It includes designated areas for routing cables, ensuring a tidy build that promotes better airflow and easier maintenance. This attention to detail further enhances the user experience, particularly for those who frequently upgrade or modify their systems.

Furthermore, the Antec SLK3700AMB provides tool-free drive installation, making it simple to set up hard drives and optical drives without the need for additional tools. Overall, the Antec SLK3700AMB stands out as a versatile and practical choice for both casual users and advanced builders, delivering a robust combination of features, performance, and style.