Device Installation, Cooling System, TriCool fan

6.Rear Right Speaker Out Pin: Connect the RET-R connector to this pin.

7.Rear Left Speaker Out Pin: Connect RET-L connector to this pin.

3.5" DEVICE INSTALLATION

With the front bezel facing you, swing the front door out. You can see there are four 5.25" and two 3.5" external drive bays. Inside the case there are four 3.5" drive cages.

1.Pull the quick release lever towards the rear of the case and release the top cage first. Looking from the rear of the case you can see some metal grills over the exposed (external) drive bays. Carefully put a screwdriver through the metal grill and gently push the plastic drive bay cover until it comes off. Carefully use your hands to twist the metal plate back and forth until it breaks off.

Note: Don't take off the covers and plates for the drive bays that you are not using now. Be careful of the newly exposed metal where the grills were attached, as these areas are likely to be sharp.

2.Install your floppy drive into the top drive bay.

3.Mount your other 3.5" device into the drive cage.

4.Slide and lock the drive cage back into the case.

5.Release the second cage.

Note: Inside the cage you will find a fan bracket. If you want to have a cooling fan in the drive cage, you should install the fan before installing the drives. For fan installation please see the Fan installation section of this manual.

6.Mount your other 3.5" devices into the drive cage.

7.Slide and lock the drive cage back into the case.

8.Find a small 4-pin connector on the power supply and connect it to the male 4-pin connector on the floppy drive.

9.Connect the appropriate power connector from the power supply to each device.

5.25" DEVICE INSTALLATION

1.Take off the plastic drive bay covers and metal plates as described above.

2.Take two of the drive rails and mount them to the sides of the 5.25" device. Make sure the metal portion is angled away from the device and facing forward.

3.Slide the device into the drive bay until you hear a click.

4.Mount the other devices accordingly. Connect a large 4-pin connector from the power supply to the male 4-pin connector on each of the devices.

COOLING SYSTEM

The TriCool fan

The case includes one 120mm TriCool fan installed in the rear. This fan has a three-speed switch that lets you choose between quiet, performance, or maximum cooling.

(See specifications below.) The fan is installed so that the air is blowing out of the case. Connect a large 4-pin connector from the power supply to the male 4-pin connector on the fan.

Note: The minimum voltage to start the fan is 5V. We recommend our users to set the fan speed to High if you choose to connect the fan to a fan control device or to the Fan-Only connector found on some of Antec's power supplies. A fan-controlled-device regulates the fan speed by varying the voltage to it. The voltage may start as low as 4.5 V to 5V. Connecting a TriCool set on Medium or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan control device will be further reduced by the TriCool circuitry below 5V.

1088AMG, TX1050B specifications

The Antec 1088AMG and TX1050B are two prominent computer cases that cater to the needs of gamers and PC enthusiasts, offering a blend of functionality, aesthetics, and expandability. Both models stand out in the crowded market of PC enclosures, showcasing their unique features and technologies.

Starting with the Antec 1088AMG, this mid-tower case is designed with an emphasis on cooling and airflow. It boasts a sleek black finish, complemented by a sturdy steel construction that ensures durability. The case features a spacious interior, allowing for easy installation of high-end components and ample room for cable management. Its front panel includes two USB 2.0 ports, audio inputs, and a power/reset button, providing convenient access for users.

The cooling capabilities of the 1088AMG are noteworthy, with support for multiple fans. The case comes pre-equipped with two120mm fans, one at the front and one at the rear, promoting efficient airflow. Additionally, the case supports extra fan placements, which can be crucial in keeping high-performance components, such as powerful graphics cards and CPUs, from overheating during intensive tasks.

Transitioning to the TX1050B, this model emphasizes versatility and expandability. It features a classic design with a glossy black front panel and a perforated metal side panel for enhanced ventilation. Similar to the 1088AMG, the TX1050B is designed for optimal airflow with support for several cooling options. It can accommodate up to five fans, ensuring that the interior remains cool even under heavy loads.

The TX1050B also understands the importance of space and organization. It includes seven expansion slots, enabling users to install multiple graphics cards or other expansion cards. The case has dedicated cable management features, allowing for tidy wiring and enhanced airflow. Additionally, the tool-less drive bays simplify the installation of hard drives and optical drives, making the building process straightforward.

Both the Antec 1088AMG and TX1050B support a wide range of Motherboards, from Micro-ATX to ATX, making them flexible choices for various build configurations. The cases also include dust filters to keep the interior clean and maintain performance.

In conclusion, the Antec 1088AMG and TX1050B provide solid performance, excellent thermal solutions, and user-friendly features. Their designs cater to those who demand reliability and expandability from their computer cases, ensuring they can build robust systems that can handle demanding applications. Whether for gaming or general use, these cases offer a comprehensive package for any PC builder.