D-Link ethernet managed switch Description Power, Console, Port LEDs, 10GE Ports, Combo SFP Ports

Page 14

 

 

 

xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch

 

 

 

 

 

 

 

 

 

 

LED

 

Description

 

 

 

 

 

 

 

 

Power

 

This LED will light green after powering the Switch on to indicate the ready state of the

 

 

 

device. The indicator is dark when the Switch is no longer receiving power (i.e powered

 

 

 

 

 

off).

 

 

 

 

 

 

 

 

Console

 

This LED will blink green during the Power-On Self Test (POST). When the POST is

 

 

 

finished, the LED goes dark. The indicator will light steady green when an active console

 

 

 

 

 

link is in session via RS-232 console port.

 

 

 

 

 

 

 

 

RPS

 

This LED will light when the internal power has failed and the RPS has taken over the

 

 

 

power supply to the Switch. Otherwise, it will remain dark.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

One row of LEDs for each port is located above the ports on the front panel. The indicator

 

 

 

 

 

above the left side of a port corresponds to the port below the indicator in the upper row

 

 

 

 

 

of ports. The indicator above the right side of a port corresponds to the port below the

 

 

Port LEDs

 

indicator in the lower row of ports. A steady green light denotes a valid 1000Mbps link on

 

 

 

the port while a blinking green light indicates activity on the port (at 1000Mbps). A steady

 

 

 

 

 

 

 

 

 

 

orange light denotes a valid 10 or 100Mbps link on the port while a blinking orange light

 

 

 

 

 

indicates activity on the port (at 100Mbps). These LEDs will remain dark if there is no link

 

 

 

 

 

on the port.

 

 

 

 

 

 

 

 

10GE Ports

 

A steady green light denotes a valid link on the port while a blinking green light indicates

 

 

 

activity on the port. These LEDs will remain dark if there is no link on the port.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED indicators for the Combo ports are located above the ports and numbered 1 – 4 for

 

 

Combo SFP Ports

 

Combo 1, Combo 2, etc. ports. A steady green light denotes a valid link on the port while

 

 

 

a blinking green light indicates activity on the port. These LEDs will remain dark if there is

 

 

 

 

 

 

 

 

 

 

no link on the port.

 

 

 

 

 

 

 

 

Stack ID

 

These two seven segment LEDs display the current switch stack order of the Switch while

 

 

 

in use.

 

 

 

 

 

 

 

 

 

 

 

Link/Act/Speed and PoE

To change the LED mode from Link/Act/Speed to PoE and vice versa, press the LED

 

 

(DGS-3426P only)

 

Mode Select Button. The Link/Act/Speed LED will light solid green when selected and will

 

 

 

 

 

shut off when PoE is selected. Likewise, when Link/Act/Speed is selected, the PoE LED

 

 

 

 

 

shuts off and the Link/Act/Speed LED lights solid green.

 

 

 

 

 

 

 

 

5

Image 14
Contents Hardware Installation Guide Page Vcci Warning Table of Contents Page Typographical Conventions CommandIntended Readers Convention DescriptionSafety Instructions Safety CautionsGeneral Precautions for Rack-Mountable Products Page Section Switch DescriptionIntroduction Ports DGS-3426 DGS-3426P DGS-3427 DGS-3450Front-Panel Components Front Panel View of the DGS-3426 DGS-3426PLED Indicators LED Indicators on DGS-3450Port LEDs Description PowerConsole 10GE PortsRear Panel Description Rear panel view of the DGS-3426 DGS-3426PSide Panel Description 13 Side Panel view of the DGS-3450Installation Guidelines InstallationPackage Contents Installing the Switch without the Rack Installing the Switch in a RackPower Failure Mounting the Switch in a Standard 19 RackPower On Installing the SFP Ports Inserting the fiber-optic transceivers into the DGS-3426Optional Module Front Panel of the DEM-410XInstalling the Module Inserting the optional module into the Switch DGS-3450External Redundant Power System DGS-3450 with the DPS-500 chassis RPSPage Switch to Switch Connecting the SwitchSwitch to End Node Connecting To Network Backbone or Server Introduction to Switch Management Management OptionsConnecting the Console Port RS-232 DCE To connect a terminal to the console portManaging the Switch for the First Time Initial Screen after first connectionPassword Protection Creating an Account on the SwitchTraps Snmp SettingsIP Address Assignment MIBsShow switch command Assigning the Switch an IP Address Web-based Switch Configuration IntroductionEnter Network Password window Logging in to the Web ManagerArea Function Web-based User InterfaceArea Web Pages Technical Specifications Appendix aStorage Temperature Physical and Environmental Internal Power SupplyOperating Temperature DimensionsRJ-45 Pin Assignments Cables and ConnectorsAppendix B Standard Media Type Maximum Distance Cable LengthsAppendix C Glossary Page Page Page Product Registration Tech Support Technical SupportTechnical Support Technische Ondersteuning Pomoc techniczna Teknistä tukea asiakkaille Suomessa Suport tehnic Egypt Australia Link Middle East Dubai, U.A.EIndia Singapore, Thailand, Indonesia, MalaysiaBahrain Украина Россия ГрузияLietuva EestiSoporte Técnico Suporte Técnico Link友訊科技 台灣分公司 技術支援資訊 Dukungan Teknis ディーリンクジャパン Web サイト 技术支持 Registration Card All Countries and Regions Excluding USA