D-Link ethernet managed switch manual Show switch command

Page 32

xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch

The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found by entering the command "show switch" into the command line interface, as shown below.

DGS-3450:admin#show

switch

Command: show switch

 

Device Type

: DGS-3450 Gigabit Ethernet Switch

MAC Address

:

00-22-B0-DE-F0-46

IP Address

:

10.90.90.90 (Manual)

VLAN Name

:

default

Subnet Mask

:

255.0.0.0

Default Gateway

:

0.0.0.0

Boot PROM Version

:

Build 1.00-B13

Firmware Version

:

Build 3.00.B10

Hardware Version

:

A2

System Name

:

 

System Location

:

0 days, 0 hours, 12 minutes, 26 seconds

System Uptime

:

System Contact

:

 

Spanning Tree

: Disabled

GVRP

: Disabled

IGMP Snooping

: Disabled

MLD Snooping

: Disabled

RIP

: Disabled

RIPng

: Disabled

TELNET

: Enabled (TCP 23)

WEB

: Enabled (TCP 80)

SNMP

: Disabled

CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All

Figure 4 - 4 “show switch” command

The Switch's MAC address also appears in Switch Information menu of the web-based management interface. The IP address for the Switch must be set before it can be managed with the Web-based or SNMP manager, Telnet or SSH. The Switch IP address can be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the Switch must be known. The IP address may be set using the Command Line Interface (CLI) over the console serial port as follows:

Starting at the command line prompt, enter the command:

config ipif System ipaddress xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy

Where the x's represent the IP address to be assigned to the IP interface named System and the y's represent the corresponding subnet mask. Alternatively, the user can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x's represent the IP address to be assigned to the IP interface named System and the z represents the corresponding number of subnets in CIDR notation. The IP interface named System on the Switch can be assigned an IP address and subnet mask, which can then be used to connect a management station to the Switch's Telnet or Web-based management agent.

23

Image 32
Contents Hardware Installation Guide Page Vcci Warning Table of Contents Page Command Intended ReadersTypographical Conventions Convention DescriptionSafety Instructions Safety CautionsGeneral Precautions for Rack-Mountable Products Page Section Switch DescriptionIntroduction Ports DGS-3426 DGS-3426P DGS-3427 DGS-3450Front-Panel Components Front Panel View of the DGS-3426 DGS-3426PLED Indicators LED Indicators on DGS-3450Description Power ConsolePort LEDs 10GE PortsRear Panel Description Rear panel view of the DGS-3426 DGS-3426PSide Panel Description 13 Side Panel view of the DGS-3450Installation Guidelines InstallationPackage Contents Installing the Switch without the Rack Installing the Switch in a RackPower Failure Mounting the Switch in a Standard 19 RackPower On Installing the SFP Ports Inserting the fiber-optic transceivers into the DGS-3426Optional Module Front Panel of the DEM-410XInstalling the Module Inserting the optional module into the Switch DGS-3450External Redundant Power System DGS-3450 with the DPS-500 chassis RPSPage Switch to Switch Connecting the SwitchSwitch to End Node Connecting To Network Backbone or Server Introduction to Switch Management Management OptionsConnecting the Console Port RS-232 DCE To connect a terminal to the console portManaging the Switch for the First Time Initial Screen after first connectionPassword Protection Creating an Account on the SwitchSnmp Settings IP Address AssignmentTraps MIBsShow switch command Assigning the Switch an IP Address Web-based Switch Configuration IntroductionEnter Network Password window Logging in to the Web ManagerArea Function Web-based User InterfaceArea Web Pages Technical Specifications Appendix aPhysical and Environmental Internal Power Supply Operating TemperatureStorage Temperature DimensionsRJ-45 Pin Assignments Cables and ConnectorsAppendix B Standard Media Type Maximum Distance Cable LengthsAppendix C Glossary Page Page Page Product Registration Tech Support Technical SupportTechnical Support Technische Ondersteuning Pomoc techniczna Teknistä tukea asiakkaille Suomessa Suport tehnic Australia Link Middle East Dubai, U.A.E IndiaEgypt Singapore, Thailand, Indonesia, MalaysiaBahrain Россия Грузия LietuvaУкраина EestiSoporte Técnico Suporte Técnico Link友訊科技 台灣分公司 技術支援資訊 Dukungan Teknis ディーリンクジャパン Web サイト 技术支持 Registration Card All Countries and Regions Excluding USA