Allied Telesis AR700 Series manual Pressing key... Forces the router to, Message Meaning

Page 35

Hardware Reference

35

displayed changes the router start-up process as described in the following table.

Table 4: Router start-up sequence keystrokes

Pressing key... Forces the router to...

(no key pressed) After a few seconds, the router startup process continues.

[Y]Load the version, without any patches, from EPROM onto the RAM, and run the full version. Go to step 6.

[S]Load and run the version and patch determined by the INSTALL parameters from the flash file system, ignoring any boot script or any previous configuration stored in NVS.

[N]Load from flash to RAM the version and patch determined by the INSTALL parameters, and run using the current configuration stored in NVS (if any), ignoring any boot script.

During the start-up process the router generates four different types of messages. All messages are preceded by one of the words INFO, PASS, FAIL, or ERROR. The meaning of these words in the context of the messages is shown in the following table.

Table 5: Router start-up message classes

Message

Meaning

 

 

INFO

An informational message that an action has been taken by the system.

 

 

PASS

An informational message that a test has been completed successfully.

 

 

ERROR

An error message that a test has failed, but the system will continue to

 

operate.

 

 

FAIL

An error message that a fatal error condition has caused the system to

 

halt in an unrecoverable fashion.

 

 

WARNING

A serious error has occurred, which may indicate hardware failure.

 

 

The possible messages and their meanings are:

INFO: Self tests beginning.

The code loader tests are about to begin.

INFO: RAM test beginning.

The RAM tests are about to begin.

PASS: RAM test, 65536k bytes found.

The RAM test passed, and the indicated amount of memory was found and will be used in the router.

ERROR: RAM test 5. Error address = 00345678.

A RAM test failed, at the given address. In the example, it was the fifth test run. The RAM test repeats until it passes, so a number of messages like this may appear. This fault means that the memory system is faulty. If the fault continues, contact your distributor or reseller immediately.

INFO: BBR tests beginning.

The BBR tests are about to begin.

PASS: BBR test. Battery OK.

The BBR battery test passed.

C613-03087-00 Rev E

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
Hardware Reference AR700 Series Router Contents Models Covered By This Reference Where To Find More InformationIntroduction Model Eth Ports AR700 Series RoutersHardware Reference AR700 Series EthernetAR725 Router Hardware FeaturesPower Supply Redundant Power Supply RPS VCC Pin Function DirectionFront panel Rear panel Do not remove the compact flash card when the LED is litAR725 LEDs and what they mean 10AR700 Series RouterFront and Rear Panels AR745 RouterAR700 Series Router DC Power inlet terminals on an AR745 DB25 RPS power connector pin out on the AT-AR745 LNK/ACT AR745 LEDs and what they meanAR700 Series Router Front Panel AR750S RouterPower Supply PIC1 AR750S LEDs and what they meanState Function PIC0AR750S-DP Router PSU Bay Two PWR03 DC installedRestart with default configuration AT-PWR03 Power SuppliesAR700 Series Router AR750S-DP LEDs and what they mean AR770S Router Front Panel Switch SFP EthAsynchronous port PIC bays AR770S LEDs and what they mean To view a document To Access DocumentationTo install any of the tools included on the CD-ROM Online DocumentationTo load a file from AT-TFTP Server to the router If AT-TFTP Server has not yet been installedAT-TFTP Server To set preferences for the AT-TFTP ServerUsing Windows Terminal Hyperterminal Hardware Reference AR700 Series Router Router Start-up Force Eprom download Y? Message Meaning Pressing key... Forces the router toStart-up tests have finished Memory Random Access Memory RAMPIC 38AR700 Series RouterOnboard Flash Memory Battery-Backed RAM AR725, AR745, AR770S onlyShow file CompactFlash AR725, AR745 only Installing and removing a compact flash cardTo test a card, insert the card and enter Expansion Options AR740 RPS Redundant Power Supply AT-AR725, AT-AR745 onlySpecifications Dimensions AR740 RPS LEDs Product No Media Type Description SFP Ports AR770S onlyPICs and NSMs AT-AR061 Ecpac PCI Accelerator Cards PACsCompression Ratio Compression → encryption →//→ decryption → decompression Asynchronous Interfaces RJ-45 Pin Function Signal DirectionCableFigure Cables and Loopback PlugsRS-232 Terminal and Modem Cables RJ-45 Hardware Reference RJ-45 To router RJ-45 DB9 Male To router To modem RJ45 MiniDin To switch or router To Macintosh Loopback Plugs for Testing InterfacesEthernet twisted pair TP loopback plug Physical Interface Loopback Pin Wiring DiagramTest failure Test FacilityEnable test int=portn Restart the router Restricted Maintenance ProceduresDiagnostics Connect a terminal to the console portKey Function Hardware Reference Enable diagnostics mode during start-upContacting Us Lithium Battery Replacement
Top Page Image Contents