Linksys SRW224P manual Uplinking the Switch, Rack-Mount Placement

Page 17

24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet

Rack-Mount Placement

To rack-mount the Switch in any standard 19-inch rack, follow the instructions described below.

1.Place the Switch on a hard flat surface with the front panel faced towards your front side

2.Attach a rack–mount bracket to one side of the Switch with the supplied screws.

3.Secure the brackets tightly.

4.Follow the same steps to attach the other bracket to the opposite side.

5.After the brackets are attached to the Switch, use suitable screws to securely attach the brackets to any standard 19-inch rack.

6.Connect the Switch to network devices according to the Hardware Installation instructions above.

Uplinking the Switch

To uplink the Switch, connect one end of a Cat5 (or better) cable into one of the 24 10/100 ports, and then connect the other end of the cable into the peripheral device’s uplink port. MDI/MDIX will automatically detect the speed and cable type.

The hardware installation is complete. Proceed to Chapter 4: Configuration using the Console Interface, for directions on how to set up the Switch.

Chapter 3: Connecting the Switch

Uplinking the Switch

Figure 3-3: Attaching Brackets to the Switch

IMPORTANT: Make sure to use the power cord that is supplied with the Switch. Use of a different power cord could damage the Switch.

Figure 3-4: Mounting the Switch

9

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Port 10/100 + 2-Port Gigabit Switch Copyright and Trademarks How to Use This User GuideTable of Contents Appendix B Cabling Appendix a Fast Ethernet and Gigabit EthernetHelp About Fast Ethernet About Gigabit EthernetFront Panel List of Figures24 Port Configuration 28 QoS IP Precedence/DSCP 61 Spanning Tree Port/LAG Info Welcome IntroductionWhat’s in this Guide? LEDs Getting to Know the SwitchFront Panel Ports Back PanelSide Panel Console Port RJ-45 PortsGigabit Expansion Ports Maximum Cabling Distances Connecting the SwitchOverview Fast Ethernet Considerations Pre-Installation ConsiderationsDesktop Placement Hardware InstallationPlacement Options Rack-Mount Placement Uplinking the SwitchConfiguring the HyperTerminal Application Configuration using the Console InterfaceSwitch Screens Configuring the Switch through the Console InterfaceSwitch Main Menu General Information VersionsCPU Performance Management SettingsSerial Port Configuration 13 User and Password Settings User and Password SettingsIP Address Settings IP ConfigurationSnmp Network Configuration19 File Management File ManagementReboot System Restore System Default Setting22 Back to Main Menu Back to Main MenuPort Status Port ConfigurationPort PoE Status PoE ConfigurationSystem PoE Configuration Logout Port PoE ConfigurationConfiguring the Switch through the Web Utility System Description System InformationSys. Info System Mode System ModeForwarding Database Address Table SettingsStatic address Dynamic AddressSys. Info Time Synchronization Screen Time Synchronization10 Sys. Info CPU Performance CPU PerformanceIP Address IP ConfigConfiguring the Switch through the Web Utility IP Config Port Configuration Switch Config14 Edit Port Configuration Screen Edit Port ConfigurationConfiguring the Switch through the Web Utility Switch Config Vlan 16 Adding/Editing Vlan Screen Create VlanVlan Port 17 Switch Config Vlan Port18 Switch Config LAG Configuration LAG ConfigurationLAG Broadcast Control Vlan LAG ConfigurationCreate LAG Port Mirroring 22 Switch Config Port MirroringLacp Membership LacpQoS Traffic Type Class of Service SettingsCoS to Queue Queue Settings28 QoS IP Precedence/DSCP IP Precedence/DSCP29 QoS IP Port IP Port30 QoS ACL Priority ACL PriorityRate Limit Rate Limit ConfigurationDiffServ DiffServ Class Map Setting Rules34 DiffServ Class Map Adding a Class Adding a ClassAdding a Policy DiffServ Policy Map37 DiffServ Policy Map Setting Rules 38 DiffServ Diffserv Service Policy DiffServ Service PolicyACL Conf SecurityExtended ACL Standard ACLConfiguring the Switch through the Web Utility Security MAC ACL 802.1xUsers ACL Port Binding44 Security 802.1x Users Radius Server 802.1xPort ConfStorm Control Port SecuritySystem Password Https SettingsSntp Global SettingsInterface Statistics StatisticsRmon Statistics Etherlike StatisticsPoE Power ConfigPower Port Status Power Port ConfigSoftware Version Power StatusSpanning Tree 59 Spanning Tree Information InformationPort/LAG Info Configuration62 Spanning Tree Information Port/LAG ConfSnmp Snmp ConfigIgmp 64 Igmp Igmp Conf Igmp ConfIgmp Router Conf Igmp Router InfoIgmp Member Conf IP Multicast Reg TableFile Download MaintenanceReset File Upload Restore DefaultsSave Config Integrated Cable Test HelpAbout Gigabit Ethernet Appendix a Fast Ethernet and Gigabit EthernetAbout Fast Ethernet Fiber Optic Cabling Appendix B CablingTwisted Pair Cabling Appendix C Glossary Appendix C Glossary Appendix C Glossary Standards Ieee Std Ports Appendix D SpecificationsCabling Type UTP CAT 5e or better LEDs System, Link/Act, PoE, Speed, Gigabit 1, GigabitLimited Warranty Appendix E Warranty InformationFCC Statement Appendix F Regulatory InformationPage Power Cord Set Cable de longueur inferieure a` 2 metres Environmental Statement Page Information section in this Guide Appendix G Contact InformationNeed to contact Linksys?

SRW224P specifications

The Linksys SRW224P is a versatile and efficient managed switch that caters to the needs of small to medium-sized businesses. This Layer 2 switch stands out with its robust functionality and user-friendly design, making it an ideal choice for networking professionals looking to enhance their network infrastructure.

One of the standout features of the SRW224P is its 24 Gigabit Ethernet ports, which provide high-speed connectivity for various devices across the network. This is particularly beneficial in environments with bandwidth-hungry applications, such as data transfers, video conferencing, and online collaboration tools. Additionally, the switch comes with 2 dual-personality ports that can be used as either Gigabit Ethernet or SFP (Small Form-factor Pluggable) ports, allowing for flexible and scalable network setups.

Power over Ethernet (PoE) capability is another significant aspect of the SRW224P. With a total PoE output of up to 370 watts, the switch can power devices such as IP cameras, VoIP phones, and wireless access points directly through the Ethernet cable, simplifying the installation process and reducing cable clutter. This feature is particularly advantageous for organizations seeking to deploy network devices in areas where power outlets are limited.

The SRW224P also boasts advanced management features, including VLAN support for segmenting network traffic, Quality of Service (QoS) for prioritizing critical applications, and Spanning Tree Protocol (STP) for redundant network paths. These capabilities enhance network performance and reliability, ensuring that users experience minimal downtime and efficient data flow.

Security is a top priority with the SRW224P, which includes features such as port security, access control lists (ACLs), and DHCP snooping. These measures help protect the network from unauthorized access and potential attacks, safeguarding sensitive information and maintaining operational integrity.

In terms of user interface, the Linksys SRW224P is equipped with a web-based management interface that allows for easy configuration and monitoring. This intuitive interface enables IT administrators to manage the switch remotely, providing real-time insights into network performance and facilitating troubleshooting.

Overall, the Linksys SRW224P managed switch combines high performance, advanced features, and security measures that make it a reliable choice for businesses aiming to optimize their network infrastructure. Its PoE capabilities, extensive port options, and management features ensure that it meets the demands of modern networking environments, making it a valuable asset for any organization.
Top Page Image Contents