Linksys SRW224P manual Configuring the Switch through the Web Utility

Page 32

24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet

Chapter 5: Configuring the Switch through the Web Utility

Overview

 

Open your web browser and enter 192.168.1.254 into the address field. Press the Enter key and the Password

 

screen will appear. The first time you open the Web-Based Utility, use the default username admin, and leave the

 

password blank. Click the OK button. You can set a new password later from the Security tab’s System Password

Figure 5-1: Address Field

screen.

 

 

 

 

 

 

NOTE: The default IP address is 192.168.1.254. If the IP address has been

 

 

changed using DHCP or the console interface, enter the assigned IP address.

 

 

 

 

 

 

The first screen that appears displays the System Description screen for the Sys.Info tab. There are 14 tabs that

 

run across the top of the screen: Sys.Info, IP Conf, Switch Conf., QoS, DiffServ, Security, SNTP, Statistics, PoE,

 

Spanning Tree, SNMP, IGMP, Maintenance and Help. Each tab contains further screens, described in this chapter,

 

to help you configure and manage the Switch.

 

 

 

 

Figure 5-2: Password Screen

Figure 5-3: Sys. Info - System Description

24

Chapter 5: Configuring the Switch through the Web Utility

Overview

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Port 10/100 + 2-Port Gigabit Switch How to Use This User Guide Copyright and TrademarksTable of Contents Appendix a Fast Ethernet and Gigabit Ethernet Appendix B CablingHelp About Fast Ethernet About Gigabit EthernetList of Figures Front Panel24 Port Configuration 28 QoS IP Precedence/DSCP 61 Spanning Tree Port/LAG Info Introduction WelcomeWhat’s in this Guide? LEDs Getting to Know the SwitchFront Panel Ports Back PanelSide Panel Console Port RJ-45 PortsGigabit Expansion Ports Maximum Cabling Distances Connecting the SwitchOverview Pre-Installation Considerations Fast Ethernet ConsiderationsDesktop Placement Hardware InstallationPlacement Options Uplinking the Switch Rack-Mount PlacementConfiguration using the Console Interface Configuring the HyperTerminal ApplicationConfiguring the Switch through the Console Interface Switch ScreensSwitch Main Menu Versions General InformationCPU Performance Management SettingsSerial Port Configuration User and Password Settings 13 User and Password SettingsIP Configuration IP Address SettingsNetwork Configuration SnmpFile Management 19 File ManagementRestore System Default Setting Reboot SystemBack to Main Menu 22 Back to Main MenuPort Configuration Port StatusPort PoE Status PoE ConfigurationSystem PoE Configuration Port PoE Configuration LogoutConfiguring the Switch through the Web Utility System Information System DescriptionSystem Mode Sys. Info System ModeAddress Table Settings Forwarding DatabaseDynamic Address Static addressTime Synchronization Sys. Info Time Synchronization ScreenCPU Performance 10 Sys. Info CPU PerformanceIP Config IP AddressConfiguring the Switch through the Web Utility IP Config Switch Config Port ConfigurationEdit Port Configuration 14 Edit Port Configuration ScreenConfiguring the Switch through the Web Utility Switch Config Vlan Create Vlan 16 Adding/Editing Vlan Screen17 Switch Config Vlan Port Vlan PortLAG Configuration 18 Switch Config LAG ConfigurationLAG Broadcast Control Vlan LAG ConfigurationCreate LAG 22 Switch Config Port Mirroring Port MirroringLacp Lacp MembershipQoS Class of Service Settings Traffic TypeQueue Settings CoS to QueueIP Precedence/DSCP 28 QoS IP Precedence/DSCPIP Port 29 QoS IP PortACL Priority 30 QoS ACL PriorityRate Limit Configuration Rate LimitDiffServ Setting Rules DiffServ Class MapAdding a Class 34 DiffServ Class Map Adding a ClassDiffServ Policy Map Adding a Policy37 DiffServ Policy Map Setting Rules DiffServ Service Policy 38 DiffServ Diffserv Service PolicySecurity ACL ConfStandard ACL Extended ACLConfiguring the Switch through the Web Utility Security MAC ACL ACL Port Binding 802.1xUsers44 Security 802.1x Users 802.1xPort Conf Radius ServerPort Security Storm ControlHttps Settings System PasswordGlobal Settings SntpStatistics Interface StatisticsEtherlike Statistics Rmon StatisticsPower Config PoEPower Port Config Power Port StatusPower Status Software VersionSpanning Tree Information 59 Spanning Tree InformationConfiguration Port/LAG InfoPort/LAG Conf 62 Spanning Tree InformationSnmp Config SnmpIgmp Igmp Conf 64 Igmp Igmp ConfIgmp Router Info Igmp Router ConfIP Multicast Reg Table Igmp Member ConfFile Download MaintenanceReset File Upload Restore DefaultsSave Config Help Integrated Cable TestAbout Gigabit Ethernet Appendix a Fast Ethernet and Gigabit EthernetAbout Fast Ethernet Fiber Optic Cabling Appendix B CablingTwisted Pair Cabling Appendix C Glossary Appendix C Glossary Appendix C Glossary Appendix D Specifications Standards Ieee Std PortsCabling Type UTP CAT 5e or better LEDs System, Link/Act, PoE, Speed, Gigabit 1, GigabitAppendix E Warranty Information Limited WarrantyAppendix F Regulatory Information FCC StatementPage Power Cord Set Cable de longueur inferieure a` 2 metres Environmental Statement Page Information section in this Guide Appendix G Contact InformationNeed to contact Linksys?

SRW224P specifications

The Linksys SRW224P is a versatile and efficient managed switch that caters to the needs of small to medium-sized businesses. This Layer 2 switch stands out with its robust functionality and user-friendly design, making it an ideal choice for networking professionals looking to enhance their network infrastructure.

One of the standout features of the SRW224P is its 24 Gigabit Ethernet ports, which provide high-speed connectivity for various devices across the network. This is particularly beneficial in environments with bandwidth-hungry applications, such as data transfers, video conferencing, and online collaboration tools. Additionally, the switch comes with 2 dual-personality ports that can be used as either Gigabit Ethernet or SFP (Small Form-factor Pluggable) ports, allowing for flexible and scalable network setups.

Power over Ethernet (PoE) capability is another significant aspect of the SRW224P. With a total PoE output of up to 370 watts, the switch can power devices such as IP cameras, VoIP phones, and wireless access points directly through the Ethernet cable, simplifying the installation process and reducing cable clutter. This feature is particularly advantageous for organizations seeking to deploy network devices in areas where power outlets are limited.

The SRW224P also boasts advanced management features, including VLAN support for segmenting network traffic, Quality of Service (QoS) for prioritizing critical applications, and Spanning Tree Protocol (STP) for redundant network paths. These capabilities enhance network performance and reliability, ensuring that users experience minimal downtime and efficient data flow.

Security is a top priority with the SRW224P, which includes features such as port security, access control lists (ACLs), and DHCP snooping. These measures help protect the network from unauthorized access and potential attacks, safeguarding sensitive information and maintaining operational integrity.

In terms of user interface, the Linksys SRW224P is equipped with a web-based management interface that allows for easy configuration and monitoring. This intuitive interface enables IT administrators to manage the switch remotely, providing real-time insights into network performance and facilitating troubleshooting.

Overall, the Linksys SRW224P managed switch combines high performance, advanced features, and security measures that make it a reliable choice for businesses aiming to optimize their network infrastructure. Its PoE capabilities, extensive port options, and management features ensure that it meets the demands of modern networking environments, making it a valuable asset for any organization.
Top Page Image Contents