Linksys EF2H16, EF2H24 manual How to Install An Add-On Module, Fiber Optic Modules

Page 8

Instant EtherFast II Series

How to Install An Add-On Module

Follow these steps to install the add-on modules in the EtherFast II 10/100 Hub (EF2H16 or EF2H24).

1.Power off the hub and remove the AC power cord from the hub.

2.Remove all RJ-45 cables from the all the ports in the hub and if the hub is on a rack remove the hub from the rack

3.Using a Phillips screw driver, remove the screws holding the small cover panel on the back of the hub. The size of the panel is about 8.1cm by 3.5cm (3.1" x 1.4"). You will need the screws to secure the add-on module later.

4.Ground yourself properly and remove the add-on module from its package.

5.Hold the module so the chips and the components on the add-on module are facing up. If the module has a daughter board (a bigger board mounted on the main board of the add-on module), the bottom of the daughter board should be facing up. Insert the module into the back of the hub.

6.The add-on module will slide in until it comes to a stop. Push the module to make sure it makes a proper connection. Note: Do not use too much force, you can bend the metal panel on the add-on module.

7.Secure the module in place with the two screws.

8.If used on a rack, mount the hub back on the rack. Reconnect the RJ-45 cables and the AC Power cord. Note: do not connect any cables to the port(s) that will be used by the add-on Module (see page 11 to find which ports can't be used when using an add-on module).

9.Connect your Fiber cable or RJ-45 cable to the add-on Module. Turn on the hub.

10/100 Hubs

Fiber Optic Modules

Two different Fiber Optic modules are available for the rack-mountable 10/100 Hub (EF2H16 and EF2H24):

EF2HSC: 100BaseFX 1-Port Transceiver Module (SC)

EF2HST: 100BaseFX 1-Port Transceiver Module (ST)

Each Fiber port has two connectors, a transmit (TX) and a receive (RX). To connect two modules together, you must run a Multi-mode fiber cable from the transmit connector on one module to the receive connector on the other. If you are looking at the back of the hub, the connector on the right is the receiver and the connector on the left is the transmitter. The connectors are also labeled on the top of the fiber port. These labels can not be seen after the module is installed, so make sure that you look before you slide it in.

Each Distance Extender Modules has a switch on the back for Full Duplex or Half Duplex. The switch must be set to Half Duplex at all times, when con- necting to another Distance Extender or a Transceiver module. The Link LED will light up when there is a connection made, and the Activity (ACT) LED will flicker while data is being transmitted or received.

Note: The duplexing switch (located on the back of the hub) should be set in Half Duplex mode. The 10/100 Hubs do not function in full duplex mode.

A maximum of 2 Transceivers can be connected together in one segment. When two hubs are connected via Transceivers together, the same rule of cas- cading two 100Mb hubs applies to them. To cascade another hub to these two hubs (using RJ-45), a switch or repeater must be used.

The Distance Extender is a switched port. This means another 100Mb hub can be cascaded (with RJ-45) to the hub that has a Distance Extender Module installed. Two Distance Extender modules can be connected together only at Half Duplex. Do NOT set either or both of the Distance Extender modules to Full Duplex. The 10/100 Hubs will not communicate at Full Duplex.

10

11

Image 8
Contents EtherFast 10/100 Hubs Copyright & Trademarks Table of Contents IntroductionPlanning Your Network OverviewLEDs Getting to Know the 10/100 HubAbout Fast Ethernet Connecting Nodes to the 10/100 Hub Powering on the HubResetting the Hub Optional Fiber Expansion ModuleCrimping Your Own Network Cables AppendixTwisted-Pair Cabling How to Install An Add-On Module Fiber Optic ModulesMaximum distance 0f 208 meters Specifications Linksys Warranty InformationEnvironmental Customer SupportCopyright 2000 Linksys, All Rights Reserved