ADC MLN7400 manual Setup EVB7400 Environments, Ethernet 10/100 BASE-T Connector

Page 13
Chapter 3 Setup EVB7400 Environments

EVB7400

Chapter 3 Setup EVB7400 Environments

3.1Ethernet 10/100 BASE-T Connector

Same connector and pin for both 10Base-T and 100 Base-Tx

<At the network interface card/hubs >

<At the cables >

RJ45 female connetor at the network interface cards and hubs

RJ45 male connector at the cable

Pin

Name

Descriptions

1

TX+

Tranmit Data+

2

TX-

Tranmit Data-

3

RX+

Receive Data+

4

N/C

Not Connected

5

N/C

Not Connected

6

RX-

Receive Data-

7

N/C

Not Connected

8

N/C

Not Connected

NOTE : TX & RX are swapped on hub

3.2Connection Method for UTP Cable

RJ45 pins on EVB7400 is defined to Adapter side. So, you straight connect EVB7400 to hub through UTP cable. In this case, between the EVB7400 and the Hub, the pin numbers correspond to each other.

Between the EVB7400 and the NIC which is on the Host PC, you have to connect each other through UTP cable which is crossover patch cord.

User’s Manual V.0.10

13/36

Copyright © 2004 MCS LOGIC Limited. All rights reserved

Image 13
Contents MLN7400 Evaluation Board Manual Version December 31 MCS Logic IncCost Effective Network Processor for TCP/IP with ARM7TDMI Copyright 2003 MCS LOGIC Limited. All rights reservedRevision History EVB7400Revision Description Version3/36 4.2.1 Table of ContentsDownloading Binary Image 4.2.2BLOCK DIAGRAM TOP VIEW EVB7400 BLOCK DIAGRAMPROPERTIES SETTING PAGE CHOOSE SETTING PAGE1.1 System Requirements Chapter 1 IntroductionFi gu re ADDRESS Fi gu re 3 BLOCK DIAGRAM TOP VIEW 1.2 Board ComponentsA Flash ROM External Interrrupt Key External Timer0 Clock2.2 Boot ROM and ROM Bank0 length Selection SW2 Chapter 2 Board Configuration2.1 Endian Selection SW1 2.3 NAND FLASH128-TQFP/ 144 -LQFP Common I/O 2.4 GPIO Setting144 -LQFP Extended I/O 선택적으로 사용3.1 Ethernet 10/100 BASE-T Connector Chapter 3 Setup EVB7400 Environments3.2 Connection Method for UTP Cable Fi gu re 4 UTP CABLE CONNECTION 4.1 Configuration the Hyper Terminal Chapter 4 Connection Configurations for Debug Console4.2.1 Downloading Binary Image 4.2 Downloading Binary Image and Flash Write2. Type “8” at Flash Program Menu and type address to download File Name Select the file name, which you want too download 3. select the Send File from the Transfer menuProtocol Select the Xmodem or 1K Xmodem 4. Click Ok Then, the file that you selected will be downloaded4.2.2 Flash Write 5.2 Connecting EVB7400 and PC Chapter 5 Opennice32 Installation5.3 Powering up the Board and OPENice32 5.1 OPENice326.1 EVB7400 BOM Chapter 6 EVB7400 1.0 Schemetic and BOMGEOMETRY COUNT22/36 23/36 6.2 EVB7400 Schematic MLN7400 Evaluation Board BLOCK DIAGRAMMLN7400EV OPTIONAL Endian SettingLITTLE SYSTEM CLOCKMLN7400P128TQFP JUMP SPI EEPROM IIC EEPROMExternal Interrupt Test EXTINTMLN7400EN FLASHBANK2 SDRAM BANKpin32 0f AC101L pins 0f AC101LPlace close to Place close toUART1 UART0UART2 UART3PCMCIA INTERFACE BANK3POWER LED JTAG CONNECTORRESET SYSTEM 7 Pin GroundHEADER IIC & SPIDATA HIGH SPEEDDisable EnableMUTE JACKAOUTL AOUTRAOUTR S AOUTL SMLN7400 NANDFlash