ADC MLN7400 manual EVB7400, A Flash ROM, Copyright 2004 MCS LOGIC Limited. All rights reserved

Page 9
A Flash ROM

EVB7400

A Flash ROM

There is a socket(U9) which accept 512Kbyte size of 8 bit Flash Memory(AT29C010 ~ 40). This is for diaganostic program(includes all pheriperal device driver and TCP/IP protocol stack) and BIOS(MCS-uClinux Boot loader) program.

User Flash memory(Selectable Boot ROM)

A mounted 48 TSOP type flash(AM29LV160BB), U8, is mounted for saving MCS-uClinux image. It has 2Mbytes(1M x 16bits)size. If you want to use this for boot ROM, SW2 should be set to to X16 and U9 should be removed. (The default setting is X8)

SDRAM

SDRAM size is 8Mbytes ( 4M x 16bits)

SRAM

There is a SRAM at ROM Bank1. SRAM SIZE is 64K x 16 bits.

NAND Flash

A mounted NAND Flash ROM is provided for saving user data.

To use NAND flash, you should install and uninstall some 0 ohm register at bottom of board. Please refer to chapter 2 and Schemetic.

EEPROM(AT24C256, AT25040)

There are two EEPROM(U3, U4). One is an IIC Serial EEPROM(U3) and the other is a SPI serial EEPROM(U4). The size of EEPROM(U3) is 32Kbytes, and the size of EEPROM(U4) is 4Kbytes.

RTC & Thermometer

There is a DS1629(U5) for RTC and thermometer check. The RTC clock is supplied by the crystal(32.768KHz)

Serial Port

There are 5 9-pin female Serial ports for serial data communiation. One is for console between the host PC and EVB7400 and others for converter(Serial to Ethernet, Serial to wireless and so on). And there is one 9-pin mail Serial ports for High Speed UART.

Ethernet Interface

There are RJ45 connector and Ethernet Phy for network.(AC101L, 10/100 BASE-T)

AUDIO IN/OUT

There is a stereo DAC(CS4340) for AUDIO out. And MIC and AMP is connected to ADIN3(ADC channel3) for AUDIO In.

Reset Button

There is a button for system reset.

Power On/Off Switch

There is a swithch for power on/off.

LED Indicatorst

Seven LEDs are supplied on the EVB7400. Each LED shows power status, user programmable status, ethernet link and activity.

PCMCIA Socket

There is a PCMCIA Socket(J2). To use it, you should set ROM BANK3 as PCMCIA mode.

JTAG Port

One 20-pin JTAG port(J3) is supplied to connect with JTAG based Emulator.

Expansion Connectors

Seven connectors(JP2~JP8) are supplied for system expansion. They contain board data bus, adddress bus, external memory bank control, IIC, SPI, and MII signals.

Key Matrix

There are 12 key buttons. They can be used ADC application.

Five buttons(SW4, SW7, SW10, SW13, SW15) are connected to ADIN0(ADC channel 0).

User’s Manual V.0.10

9/36

Copyright © 2004 MCS LOGIC Limited. All rights reserved

Image 9
Contents MLN7400 Evaluation Board Manual Version December 31 MCS Logic IncCost Effective Network Processor for TCP/IP with ARM7TDMI Copyright 2003 MCS LOGIC Limited. All rights reservedRevision History EVB7400Revision Description Version3/36 4.2.1 Table of ContentsDownloading Binary Image 4.2.2BLOCK DIAGRAM TOP VIEW EVB7400 BLOCK DIAGRAMPROPERTIES SETTING PAGE CHOOSE SETTING PAGEChapter 1 Introduction 1.1 System RequirementsFi gu re ADDRESS Fi gu re 3 BLOCK DIAGRAM TOP VIEW 1.2 Board ComponentsA Flash ROM External Interrrupt Key External Timer0 Clock2.2 Boot ROM and ROM Bank0 length Selection SW2 Chapter 2 Board Configuration2.1 Endian Selection SW1 2.3 NAND FLASH128-TQFP/ 144 -LQFP Common I/O 2.4 GPIO Setting144 -LQFP Extended I/O 선택적으로 사용Chapter 3 Setup EVB7400 Environments 3.1 Ethernet 10/100 BASE-T Connector3.2 Connection Method for UTP Cable Fi gu re 4 UTP CABLE CONNECTION 4.1 Configuration the Hyper Terminal Chapter 4 Connection Configurations for Debug Console4.2.1 Downloading Binary Image 4.2 Downloading Binary Image and Flash Write2. Type “8” at Flash Program Menu and type address to download File Name Select the file name, which you want too download 3. select the Send File from the Transfer menuProtocol Select the Xmodem or 1K Xmodem 4. Click Ok Then, the file that you selected will be downloaded4.2.2 Flash Write 5.2 Connecting EVB7400 and PC Chapter 5 Opennice32 Installation5.3 Powering up the Board and OPENice32 5.1 OPENice326.1 EVB7400 BOM Chapter 6 EVB7400 1.0 Schemetic and BOMGEOMETRY COUNT22/36 23/36 6.2 EVB7400 Schematic BLOCK DIAGRAM MLN7400 Evaluation BoardMLN7400EV OPTIONAL Endian SettingLITTLE SYSTEM CLOCKMLN7400P128TQFP JUMP SPI EEPROM IIC EEPROMExternal Interrupt Test EXTINTMLN7400EN FLASHBANK2 SDRAM BANKpin32 0f AC101L pins 0f AC101LPlace close to Place close toUART1 UART0UART2 UART3PCMCIA INTERFACE BANK3POWER LED JTAG CONNECTORRESET SYSTEM 7 Pin GroundHEADER IIC & SPIDATA HIGH SPEEDDisable EnableMUTE JACKAOUTL AOUTRAOUTR S AOUTL SMLN7400 NANDFlash