Advantech AIMB-210 user manual System Memory, Memory Installation Procedures

Page 24

1.9System Memory

The AIMB-210 has one socket for a 200-pin SODIMMx1.

All these sockets use 1.8 V unbuffered double data rate synchronous DRAMs (DDR SDRAM). They are available in capacities of 256, 512, and 1024 MB. The sockets can be filled in any combination with DIMMs of any size, giving a total memory size between 256 MB and 2 GB. AIMB-210 does NOT support ECC (error checking and correction).

1.10Memory Installation Procedures

To install SODIMMs, first make sure the two handles of the SODIMM socket are in the “open” position, i.e., the handles lean outward. Slowly slide the SODIMM module along the plastic guides on both ends of the socket. Then press the SODIMM module well down into the socket, until you hear a click when the two handles have automat- ically locked the memory module into the correct position of the SODIMM socket. To remove the memory module, just push both handles outward, and the memory mod- ule will be ejected by the mechanism.

AIMB-210 User Manual

12

Image 24
Contents AIMB-210 Copyright Acknowledgements Advantech Customer Services Message to the CustomerDeclaration of Conformity FCCMemory Compatibility Brand Size Speed Vendor PN Advantech PN MemoryProduct Warranty 2 years Ordering InformationInitial Inspection Viii Contents Chipset Software Installation Utility Appendix a Table B.24System I/O Ports Chapter Features IntroductionCost effective 945GSE chipset supports 533 Front side bus Specifications Jumpers and Connectors Industrial featuresMechanical and environmental specifications ConnectorsUSB56 Board layout Jumper and Connector Locations Jumper and Connector LocationAIMB-210 Board Diagram AIMB-210 Board DiagramSafety Precautions Jumper Settings How to Set JumpersCmos Clear CMOS1 CMOS13 COM2 RS 232/422/485 Mode Selector JSETCOM2 4 JLV1/JLV2 LCD Power 3.3 V/5 V SelectorCOM2 RS 232/422/485 Mode Selector JSETCOM2 JLV1/JLV2 LCD Power 3.3 V/5 V SelectorJPSON1 ATX, AT Mode Selector JWDT1 Watchdog Timer Output OptionJPSON1 ATX, AT Mode Selector JWDT1 Watchdog Timer Output OptionMemory Installation Procedures System MemoryConnecting Peripherals Parallel Port LPT1 Connecting Peripherals Primary IDE1 IDE ConnectorLAN LED Indicator USB Ports LAN1USB12/LAN2USB34/USB56/ USB78TV-Out Connector TVOUT1 TV-Out Connector TVOUT1VGA Connector VGA1 Serial Ports COM1~COM6 PS/2 Keyboard and Mouse Connector KBMS1 CPU Fan Connector CPUFAN1 System FAN Connector CHAFAN1 Front Panel Connectors JFP1/JFP2/JFP3 ATX soft power switch JFP1 / PwrswReset JFP1 / Reset HDD LED JFP2 / HddledPower LED and keyboard lock connector JFP3 / Pwrled ATX power supply LED status No support for AT powerLine In, Line Out, Mic In Connector AUDIO1 Serial ATA Interface SATA1, SATA2 14 PCI Front Headphone Connector FPAUD1 ATX Power Connector EATXPWR1 SPI Flash connectorSPICN1 LCD Inverter Connector INV1 & INV2 Optional Lvds Connector LVDS1 & LVDS2 Optional Digital I/O Connector DIO1 Page Bios Operation Bios Setup Control KeysMain Menu Standard Cmos Features Advanced Bios Features Advanced Chipset Features Dvmt Mode Dvmt Boot DisplaySystem Memory Frequency Auto PCI Express Root port Func Press EnterIntegrated Peripherals OnChip IDE DeviceOnboard Device Parallel Port Mode ECP+EPP EPP Mode Select EPP1.9ECP Mode Use DMA Super IO DeviceUSB Device Setting Security Chip Configuration Optional Item TPM Support Power Management Setup Suspend Mode Disabled PowerOn by LAN EnabledPowerOn by Modem Enabled USB KB WakeUp From S3 Disabled10 PnP/PCI Configurations Reset Configuration Data DisabledResources Controlled By AutoESCD PC Health Status Frequency/Voltage ControlLoad Setup Defaults Set Password Bios Operation Save & Exit Setup Quit without SavingChipset Software Installation Utility Before You Begin Windows XP Driver Setup Page VGA Setup Windows Vista/XP/2000 LAN Configuration Installation Win XP/Vista Driver Setup Realtek RTL8111CAppendix a Programming the Watchdog Timer Watchdog Timer OverviewProgramming the Watchdog Timer Appendix a Programming the Watchdog Timer Table A.1 Watchdog Timer Registers Address of Register 2E AttributeExample Program Page Appendix a Programming the Watchdog Timer Page Appendix B USB Header USB56, USB78 Table B.1 Parallel Port LPT1Table B.2 USB Header USB56 Table B.3 VGA Connector VGA1 RS-232 InterfaceTable B.4 RS-232 Interface COM1~COM4 RS-232/422/485 Setting Interface JETCOM2 SPICN1 SPI Fresh Card Pin ConnectorTable B.5 RS-232/422/485 Setting Interface JETCOM2 Table B.6 SPICN1SPI Fresh Card Pin ConnectorCPU Fan Power Connector CPUFAN1 Table B.7 PS/2 Keyboard and Mouse Connector KBMS1Table B.8 CPU Fan Power Connector CPUFAN1 System Fan Power Connector CHAFAN1 Power LED & Keyboard Lock Connector JFP3Table B.9 System Fan Power Connector SYSFAN1/SYSFAN2 Table B.10 Power LED & Keyboard Lock Connector JFP3Table B.11 External Speaker Connector JFP2/SPEAKER Table B.12 Reset Connector JFP1/ ResetTable B.13 ATX Power Connector ATX2 14 USB/LAN ports LAN1USB12/LAN2USB34Table B.14 USB Port Table B.15 Ethernet 10/100 Mbps RJ-45 Port17 AT/ATX Mode PSON1 Serial ATA0/1 SATA1/SATA218 AC-97 Audio Interface FPAUD1 Table B.19 AT/ATX Mode PSON1 Gpio Pin Header GPIO1Table B.20 LVDS1 Connector Optional Lvds Power Jumper JLV1, JLV2 Table B.21 LVDS2 Connector OptionalTable B.22 Lvds Power Jumper Table B.23 Lvds Power Jumper Lvds Invert INV1 & INV2 OptionalSystem I/O Ports Table B.24 System I/O PortsDMA Channel Assignments Interrupt Assignments26 1st MB Memory Map Appendix B I/O Pin Assignments